# A low-tech way to sand bevels (chamfers) evenly into PVC and acrylic pipes

**URL:** <https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703>\
**Category:** Tutorials & Guides\
**Created:** [December 29, 2016, 2:27am UTC](https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703 "2016-12-29T02:27:56Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Astyanax](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/a/b9e5f3/32.png) [@Astyanax](https://forum.gbfans.com/u/Astyanax)\
**Post date:** [December 29, 2016, 2:27am UTC](https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703/1 "2016-12-29T02:27:56Z")

</div>

Hey guys:

As I am getting to the end of my [proton pack scratch build](http://www.gbfans.com/forum/viewtopic.php?f=2&t=41946), it has become evident that the clear plastic tip of my proton thrower is going to want a bevel (aka chamfer) on its end. But since acrylic tubing scratches so easily, I can’t just go rubbing it on some 80-grit sandpaper.

After a few hours of trial and error with some different attempts, I came up with this simple technique to get an evenly sanded bevel on the end of my tubing. I needed my drill, a funnel, a wood dowel, glue, and my sandpaper of choice.

The first thing I did was get a 1/4 sheet of 80-grit sandpaper, and draw a circle with a compass.

 ![image](https://discdn.gbfans.com/original/3X/c/4/c4c0c8d372e44653e88cf8985072bbb40cee1381.jpeg)

Then, I cut it out, and made sure I had the center located.

 ![image](https://discdn.gbfans.com/original/3X/f/4/f4c8b2abaaf835ad066352db4659728bb8277d1d.jpeg)

Next, I sliced out about a 1/16th wedge and test fit it in the funnel (picked up for next to nothing at an auto parts store). I marked the overlap with a pen.

 ![image](https://discdn.gbfans.com/original/3X/4/1/41da5d30d22494dfb3caefaec58043d8cff5f1f2.jpeg)

After that, I cut out the excess of the sandpaper along the lines I had traced.

 ![image](https://discdn.gbfans.com/original/3X/b/c/bcdc49132af8b37001f98c45dd40d656a985bc8e.jpeg)

To glue my sandpaper cone to the inside of the funnel, I used spray adhesive. I would imagine superglue or epoxy work too, but it’s important to make sure it is a thin coat with no bumps under the sandpaper.

I also jammed a wood dowel through the funnel, just wide enough to be a tight fit through the tip.

 ![image](https://discdn.gbfans.com/original/3X/c/f/cf8dc7d103f4c3ed24c2531f07bc0f4ad1381b63.jpeg)

The dowel serves as a rod for the drill to grip onto.

Now, all I had to do was hold the drill trigger in the “on” position, and slide the tube I wanted beveled over the dowel. Pressing gently and evenly into the funnel causes the bevel to be cut into the edges of the tube.

 ![image](https://discdn.gbfans.com/original/3X/3/2/32ffb7855decd5781f67265edb6a62fab2015bc0.jpeg)

Stopping frequently and blowing out the sandpaper with spray air helps.

As you can see, the bevel is even and angled nicely.

 ![image](https://discdn.gbfans.com/original/3X/3/4/3496b2258364b18b2dafb79077bf0896f5841ac3.jpeg)

I didn’t go all the way to the edge, because this test piece of PVC is thicker than the clear tubing I’ll be using, but you get the idea.

Enjoy!

Bill

---

<div class="post-metadata">

**Author:** ![Styrofoam\_Guy](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/s/87869e/32.png) [@Styrofoam\_Guy](https://forum.gbfans.com/u/Styrofoam_Guy)\
**Post date:** [December 31, 2016, 6:11am UTC](https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703/2 "2016-12-31T06:11:00Z")

</div>

Very ingenious 🙂

---

<div class="post-metadata">

**Author:** ![jonogunn](https://forum.gbfans.com/user_avatar/forum.gbfans.com/jonogunn/32/186058_2.png) [@jonogunn](https://forum.gbfans.com/u/jonogunn)\
**Post date:** [August 13, 2023, 12:34pm UTC](https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703/3 "2023-08-13T12:34:50Z")

</div>

Just wanna say thanks for this technique. Had this page saved for years and finally got around to trying it!

 ![image](https://discdn.gbfans.com/original/3X/5/b/5b9ddd01bf6b94143e3070153a492a2015f3fb28.jpeg)

---

<div class="post-metadata">

**Author:** ![Astyanax](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/a/b9e5f3/32.png) [@Astyanax](https://forum.gbfans.com/u/Astyanax)\
**Post date:** [August 14, 2023, 5:08pm UTC](https://forum.gbfans.com/t/a-low-tech-way-to-sand-bevels-chamfers-evenly-into-pvc-and-acrylic-pipes/22703/4 "2023-08-14T17:08:40Z")

</div>

That’s awesome! So glad it worked for you, and thanks for letting me know!
