# Dan's Proton Pack builds

**URL:** <https://forum.gbfans.com/t/dans-proton-pack-builds/9627>\
**Category:** Proton Packs\
**Created:** [October 5, 2012, 6:41am UTC](https://forum.gbfans.com/t/dans-proton-pack-builds/9627 "2012-10-05T06:41:46Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![dhammans](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/d/65b543/32.png) [@dhammans](https://forum.gbfans.com/u/dhammans)\
**Post date:** [October 5, 2012, 6:41am UTC](https://forum.gbfans.com/t/dans-proton-pack-builds/9627/1 "2012-10-05T06:41:46Z")

</div>

I’ve been in the game for a few years. I originally started on this site in approximately 2005-2006. Having been a Ghostbusters fan my entire life I had always had a fascination with the traps and [proton packs](https://www.gbfans.com/wiki/equipment/proton-pack). I built my first trap in 1986 with my father for Halloween. Probably more accurately stated, my father built my first trap in 1986 for Halloween :).

When I discovered what was possible, and how much work had been done by the community I was pretty impressed. It has taken me a long time to realize the dream and actually begin building a Proton Pack, but after a couple of false starts I’m on my way.

Right now I have two shells, an Exoray V-71 MarkX, and a Bigi330 shell purchased from noslliT here on the forum. I think it’s interesting how the bar has continued to move forward, and the various debates that go on the board here about what is more accurate vs. what is more convenient or affordable. I’ve got pictures of both shells side by side to show some comparisons in the details. While they are essentially the same, the Exoray shell appears to be overall more straight, and the angles are sharper. I’m not trying to say it’s better; on the contrary I’m saying that it looks more like it came off the assembly line at a factory versus the Bigi shell which looks more like it was cooked up by Egon in the Ghostbuster laboratory. More screen accurate perhaps, but it’s a slippery slope between screen accurate and aesthetically pleasing in my opinion. I think there’s room for both approaches, and I’m excited to try two different styles of builds with these different shells.

Exoray shell with one of my Matty Collector [Ghost traps](https://www.gbfans.com/wiki/equipment/ghost-trap)

Comparison photo, Exoray shell on the left and Bigi330 shell on the right.

Right now I am working on the Exoray shell, and it will be my first “complete” build. I say “complete” because after reading these forums I realize that no pack is ever truly safe/finished. I’m planning on setting it up Ghostbusters 2 style at the moment. Someday I would like to go in the direction of a video game pack with it, but for now the first goal is to go GB2 style. I’ve been amassing parts at a somewhat staggering rate (just ask the sellers on here, they can attest to this) for both shells. The first thing I noticed when comparing the two shells is that the Exoray is significantly thicker and heavier. When I wear one to the GB3 opening, I expect I will probably take the Exoray as it looks a bit more durable.

Rub a dub dub… Proton Pack in the tub! Cleaning up any excess mold release on the Exoray shell.

So far I have the following:

Exoray V71X shell

MMM [motherboard](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard) (trimmed by hand to fit)

LC-1 style pack frame

Exoray ION arm (resin)

```
GB2 style real resistors; (I have excess of these, some from AJ and some from MMM)

	Dale RH-50

	Sage silohm 25

	Dale PH-25

```

Clippard R701 and R331s from GBFans store

Exoray resin [bumper](https://www.gbfans.com/wiki/equipment/proton-pack/bumper) (Extremely nice piece, almost identical to the Bigi/Nickatron)

Spectrastrip cable (Ebay)

aluminum shock mount/bellows (Ebay, but I’d REALLY like something better)

Cable clamp (MMM)

Exoray 3" [N-Filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter)

HGA:

```
GBFans/AJ new run aluminum HGA (very nice)

```

[Booster Tubes](https://www.gbfans.com/wiki/equipment/proton-pack/booster-tube):

```
Vincenzo aluminum booster tubes

```

Booster ladder frame (AJ/GBFans casting)

5/32" SMC elbows (MMM)

5/32" SMC straights (MMM)

GB2 style [Clippard brass elbows](https://www.gbfans.com/shop/clippard-brass-elbow) and barbs (MMM)

GBFans [aluminum beam line](https://www.gbfans.com/shop/aluminum-welded-beam-line) & filter tubes

Exoray booster tube (PVC)

Booster tube plug (Resin, purchased in 2007 from a now banned seller)

[Crank knob](https://www.gbfans.com/shop/crank-knob) (black resin, from aforementioned banned seller)

Throwing Chicken v3 kit w/ forward assembly (LOVE it)

GBFans acrylic tube

noslliT [power cell](https://www.gbfans.com/wiki/equipment/proton-pack/power-cell) and [cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron) lenses

gEkX hardware sets

```
pack x 1

throwing chicken wand x 1

```

Sound Board (AJ/GBFans)

I also just put down the $$ for GhostGuy’s Mighty Microcontroller. I may also end up picking up a Crix or Jupiter Light kit to get past the Halloween holiday if necessary.

* * *

I haven’t started the build phase for the second pack yet, but here is what I have amassed for it so far. I plan on trying to be more screen accurate with a weathered look in Ghostbusters 1 style for this pack, as opposed to the freshly manufactured Ghostbusters 2 look for the Exoray shell.

Bigi330/Vincenzo Shell

Bigi330/Vincenzo motherboard

LC-1 frame, accurate LC-1 straps from gEkX (need a kidney pad…)

Anhcon’s:

```
aluminum Injector tubes

aluminum Booster tube/plug

aluminum HGA

aluminum N-Filter

aluminum vac line

aluminum beam line & filler tube

Cable clamps

aluminum ppd

ION Rod (GB1 style)

```

Booster Ladder Frame (Nick-a-tron, thanks Mr. Tillson)

[aluminum ION arm](https://www.gbfans.com/shop/aluminum-welded-ion-arm) assembly (CPU64, by way of Mr. Tillson)

```
GB1 style real resistors installed (Thanks Mr. Tillson)

```

Clippard R701 and R331s from GBFans store

5/32" SMC elbows (MMM)

5/32" SMC straights (MMM)

GB1 style Clippard brass elbows and barbs (MMM)

I’m in the market for some real [Legris](https://www.gbfans.com/wiki/equipment/proton-pack/legris) fittings for this pack…

aluminum shock mount/bellows (Ebay, but I’d like something better…)

Bumper (Nickatron/Bigi330)

GB1 cable (GBFans/Blkmesahero)

CPU64 aluminum thrower (TRYING to get on the waiting list …)

Anhcon’s: (Ordered/paid)

```
Rear cylinder

Front cylinder

Gun track

V-Hook (GB1 style)

Trigger Tip/Forward Handle assembly

GB1 banjo tips

aluminum gun knobs/regulator knobs

loom locking system

```

b0bamatt labels from the August 2012 run

gEkX hardware sets

```
pack x 1

CPU64 wand x 1

```

Sound Board (AJ/GBFans)

GBFans Pack Blaster boards, Exoray shell with first coat of primer, and Blkmesahero GB1 [ribbon cable](https://www.gbfans.com/wiki/equipment/proton-pack/ribbon-cable).

Part of this is an experiment in terms of parts ordering, for instance I will actually have 3 sets of [Injector tubes](https://www.gbfans.com/shop/aluminum-welded-injectors) once my order from Franchesky comes in. It has slowed me down in the building process because I’ve been evaluating the different parts and trying to decide which ones I like best, and which ones fit each build best. Right now I am planning on using Franchesky’s parts for the GB1 build, so I have listed them accordingly above. I will be taking a metric s\*\*\*load of pictures through this process to give people an idea of the difference between the various parts. I will try to document some of the mundane details that some of the experienced guys on here take for granted. I’m a total newbie when it comes to prop building, but I’m an IT “Engineer” by trade so I’m fairly good at the details.

Hopefully you guys find this interesting, I’ll have more to report soon

Cheers,

Dan

---

<div class="post-metadata">

**Author:** ![zombierepellent](https://forum.gbfans.com/user_avatar/forum.gbfans.com/zombierepellent/32/5970_2.png) [@zombierepellent](https://forum.gbfans.com/u/zombierepellent)\
**Post date:** [October 6, 2012, 5:07am UTC](https://forum.gbfans.com/t/dans-proton-pack-builds/9627/2 "2012-10-06T05:07:59Z")

</div>

I can tell, this is going to be a great build thread to refer people to. I really like how you actually cover washing them. It’s important to wash everything that’s been cast.

---

<div class="post-metadata">

**Author:** ![dhammans](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/d/65b543/32.png) [@dhammans](https://forum.gbfans.com/u/dhammans)\
**Post date:** [October 8, 2012, 5:50am UTC](https://forum.gbfans.com/t/dans-proton-pack-builds/9627/3 "2012-10-08T05:50:43Z")

</div>

Thanks Zombie. Washing all of your cast parts is essential. Mold release and other chemicals left over from the casting process can make paint bubble up, or not adhere to your work. It only takes a few minutes, and I’ll have to admit I might have had a little “rub a dub dub [proton pack](https://www.gbfans.com/wiki/equipment/proton-pack) in the tub” tune in my head while doing it. 🙂

One of the first things I wanted to do in my build was get the motherboard sized properly, and attached to the shell. Being that I did not get a motherboard with my Exoray shell I used one of the MMM [motherboards](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard) that I happened to have in the closet. I spent quite a bit of time adjusting the shell onto the motherboard until I got what I felt like was the right combination of fit and cutting. Being that the MMM motherboard is cut to Stephan’s plans, most shells don’t fit it quite right.

In order to do the actual cutting I used an inexpensive jig-saw from home depot with a bit intended for cutting metal. The saw was about $40 and I purchased it for a previous project, so the only cost was a 2 pack of blades for about $8.

Shell sitting on the motherboard after being cut. Note the marker lines, I put those there to keep me from getting a little too excited with the jigsaw.

Taking your time positioning the shell and tracing what needs to be cut on the board, as well as really taking your time while cutting (even with a free-handed tool) can work really well. I’m usually not very good at this type of stuff, but I think it came out really well.

The white spots on the shell are filler. At this point I had one coat of primer on the shell - I used the Rustoleum filler primer. Their definition of filler primer is not the same as mine, for future coats I swapped to the Rustoleum auto primer that is generally recommended here.

Close up of the fitment at the bottom of the [cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron).

Next up is mounting the motherboard. Before starting I read this thread here: [Attaching motherboard to pack shell w/pics - Tutorials & Guides - GBFans.com](http://www.gbfans.com/community/viewtopic.php?f=2&t=11972). I bought some angle aluminum from home depot, but I think I spent more money on that than I did just ordering the mounting kit from gekx here on the board. I highly recommend his hardware kits, he ships fast and while you may not use everything (some of my parts came with duplicate hardware) it’s a great kit. Having a few too many is better than not enough.

I got the correct large-■■■■■■ style rivets, and the brackets from gekx, but I also made some of my own from angle aluminum from Lowes. I opted to go with the brackets from gekx for two reasons. First, they were a bit narrower (GB2 semi-hero style I believe) than the GB1 style width I cut - I laid them out next to the motherboard in the photo to illustrate why this is useful. It is much easier to measure the thickness of the shell and place the bracket on the motherboard than it is to guess where it needs to go because it is too wide to fit on a single section of the cyclotron. Second, they are thicker which gives a bit more room in it for threads. It would be a real bummer to strip the threads and have to replace one of the brackets down the road. I wanted this part of it to be safely removable a number of times to work on electronics, etc. inside the pack. Also the brackets I got from gekx were pre-drilled, which made it a lot easier to actually perform the installation. Once I had the positioning down, I started the hole on the motherboard through the bracket to place it.

Having never used rivets before I really had no idea how they worked, or how to use them. You need a rivet gun, but it’s relatively inexpensive at about $18. Both Lowes and Home Depot carry exactly the same ones, so they probably aren’t half bad. You can always use it for gutter and downspout repair as well ;). I found a great video on Youtube that explained everything, I tried to find the same one to post but I couldn’t. I don’t think it matters, there is a lot of info available. Just pick one with a presenter whose accent you like.

In order to place the lower two brackets I measured the thickness of the shell (at the thickest point) for both appropriate sections of the Cyclotron, and then marked the motherboard and placed the bracket loose. I then placed the shell on the motherboard, and using the cyclotron rings as a way to reach in and view, snugged the brackets up against the inside of the shell. After carefully removing the shell I found that my measurements were really close, but after a couple of test fits decided to go with the location determined by hand as opposed to the measurements. This turned out really well, and I’m glad I went with that positioning in hindsight.

For the [power cell](https://www.gbfans.com/wiki/equipment/proton-pack/power-cell) bracket I used the power cell window as an access point for the same procedure, although it was a little more difficult to see inside. I did the gun mount area bracket last, as I had to do it completely by measurement. At that point though I felt pretty comfortable with the process and it came out just fine.

---

<div class="post-metadata">

**Author:** ![dhammans](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/d/65b543/32.png) [@dhammans](https://forum.gbfans.com/u/dhammans)\
**Post date:** [November 14, 2012, 6:50am UTC](https://forum.gbfans.com/t/dans-proton-pack-builds/9627/4 "2012-11-14T06:50:31Z")

</div>

Sorry for the lack of updates, but I do have a picture to share.

![image](http://www.acme-labs.net/img/packbuild/willowdaddy2.JPG)

I will continue to update the thread with progress soon.
