# My GB1 Style Proton Pack/Thrower **URL:** \ **Category:** Proton Packs\ **Created:** [July 20, 2011, 12:57am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920 "2011-07-20T00:57:12Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [July 20, 2011, 12:57am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/1 "2011-07-20T00:57:12Z")
So with the uniform being pretty much complete bar 1 or two things, i thought it was time to get this thread up and running to let you all see how the [Proton Pack](https://www.gbfans.com/wiki/equipment/proton-pack) is coming along. So below is a pic of how it sits at the moment. A friend and myself started this back at the beginning of April and have spent whatever time we can on it since to get it to this point. It’s not completely finished yet as there are still a few things needing done, such as sanding, filling, shaping and of course using no nails…put together into one big piece which is then screwed to a sheet of wood, ready for moulding. Hopefully by the end of this week we should have it ready to begin the moulding process. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5634.jpg) ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [July 21, 2011, 3:01am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/2 "2011-07-21T03:01:06Z")
Just a quick update on this. Didn’t really get alot of time in on the buck 2day as i had to pick up the Silicone Rubber and Fiberglass that i will be using to make the shells from, but we managed to complete the little bits of details needing done before we begun to filler each part. Here’s a pic of the completed buck with the [N-Filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter) attached. You can also see the squares 15 squares to the left that need to be glued onto the [Synchronous Generator](https://www.gbfans.com/wiki/equipment/proton-pack/synchronous-generator) Spacer. I will attach these once all the filling and sanding is complete ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5642.jpg) Also a pic of the filling process in the early stages. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5643.jpg) ---
**Author:** ![stroudy](https://forum.gbfans.com/user_avatar/forum.gbfans.com/stroudy/32/6713_2.png) [@stroudy](https://forum.gbfans.com/u/stroudy)\ **Post date:** [July 23, 2011, 4:37pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/3 "2011-07-23T16:37:39Z")
Looking good fella ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [July 28, 2011, 12:38am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/4 "2011-07-28T00:38:39Z")
Filliers, fillers, fillers and MORE ■■■■■■ FILLERS!!! Yes, you’ve guessed it, this week has mainly been taken up by filling and sanding numerous holes, cracks, dips and joins. Saying that it has been quite exciting seeing this build at this early stage start to take shape so quickly. I remember when all of this statred with a few blueprints, a few bits of would, a measuring tape and a pencil…aahh the memories of old lol!! 😛 Anyhoo, back to the matter at hand…After making sure everything was ok and we were happen to continue, we set about the filling and sanding process, also we decided to screw each piece into place on a big woden board so that we can keep it altogether and minimise the mess. The idea of mounting it on the wall once finished has even been tossed around lol!! So here’s a pic of how she looks all filled, sanded screwed down and pilot holes drilled for other attachments ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5691.jpg) Also a pic of it just wanting to be strapped to my back…actually i think this look suits, maybe i should just keep it like this and attach the Alice Frame now?? lol!! ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5692.jpg) So once all of that was done with, we set about giving the wooden buck a coat of gloss paint to help stop the Silicone Rubber from trying to soak into the wood. With and without flash ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5700.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5699.jpg) ---
**Author:** ![KagaSakai](https://forum.gbfans.com/user_avatar/forum.gbfans.com/kagasakai/32/6197_2.png) [@KagaSakai](https://forum.gbfans.com/u/KagaSakai)\ **Post date:** [July 28, 2011, 12:50am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/5 "2011-07-28T00:50:51Z")
> [@Warrenzo](#): > > Also a pic of it just wanting to be strapped to my back…actually i think this look suits, maybe i should just keep it like this and attach the Alice Frame now?? lol!! > > ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5692.jpg) I vote that you do this! 😛 Nice work so far! ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [July 29, 2011, 1:51am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/6 "2011-07-29T01:51:42Z")
And so the scary biscuits bit begins!!! Tonight was the night to make the Silicone Rubber mould, so here is a brief description of how it was done including pics. To begin with we bought a 5.5KG tub of Silicone Rubber, a bottle of Silicone Catalyst, Thixo, Black Pigment, Release Agent,a few mixing bowls and a few paint brushes…i kinda forgot to include these in the photo, oopps!! ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4275.jpg) For the 1st layer i mixed the Silicone and Catalyst until a salmon pink colour was achieved and poured this onto the wooden buck. Using the paint brushes we spread it over the buck until it was completely covered and left it to cure until it was tacky. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4279.jpg) 1st Layer done. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4281.jpg) Once tacky, this was the cue to mix up the next batch. This time i aded a black pigment, making it easier to see where i may have missed any bits with this next layer. I also added some Thixo to thicken up the Silicone as this layer needs to be thicker. This was applied and again left to cure until tacky. 2nd Layer done ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4288.jpg) Now it was time for the third and final layer. This time i added slightly more Thixo to make it even thicker. This proved to be a little too thick, but gave the mould that “just iced” cake look. It was so good i couldn’t help myself and had to taste it just to be sure it really wasn’t iceing lol!! I got caught in the act and quickly decided this might not be such a good idea after all and set the paint brush down…unplanned trip to A&E swiftly averted 😃 ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4289.jpg) 3rd Layer done, with that oh so tempting iceing look! ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_\_MG\_4292.jpg) This is where we left it to completely cure and then it’s time for the Fiberglass jacket to be done. We’ll cover that next. ---
**Author:** ![parksdesign](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/p/77aa72/32.png) [@parksdesign](https://forum.gbfans.com/u/parksdesign)\ **Post date:** [July 29, 2011, 2:07am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/7 "2011-07-29T02:07:28Z")
Nice. ---
**Author:** ![dfak2009](https://forum.gbfans.com/user_avatar/forum.gbfans.com/dfak2009/32/12033_2.png) [@dfak2009](https://forum.gbfans.com/u/dfak2009)\ **Post date:** [July 30, 2011, 10:55pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/8 "2011-07-30T22:55:27Z")
Loving it Warren, awesome job man!!! Here come the Emerald GB’s 😉 ---
**Author:** ![gbrob](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/g/ba8739/32.png) [@gbrob](https://forum.gbfans.com/u/gbrob)\ **Post date:** [July 31, 2011, 2:41am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/9 "2011-07-31T02:41:22Z")
Git 'er done! 🙂 ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [August 11, 2011, 3:46pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/10 "2011-08-11T15:46:45Z")
Ok, time for another update. Get ready for loads of picture viewing cause this is a big one!!! So once the Silicone Rubber mould had set, it was time to break out the clay and build a fort err…i mean a wall around it. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5716.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5718.jpg) We also built a clay wall on top to make sure the Fiberglass will be seperated into twho halfs. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5719.jpg) Next it time to begin making the fiberglass jacket on top of the Rubber Silicone. For this we bought a 5kg drum of resin, Hardener, thickener, syringe, fiberglass matt and a mask to keep the smell/fumes out. Also (out of shot) we used latex gloves and a full body covering boiler suit type thing that they use for crime scene investigations. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5721.jpg) We mixed up a batch of the resin with the hardener and began to pour/paint it over one half of the rubber, making sure to cover the clay also. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5725.jpg) Once that was done we mixed up another batch, but this time added some of the thicknener. We previously had cut the fiberglass matt into good sized squares and dipped them into the mix, making sure it soaked in well and covered the whole of the 1st half right up to and including the clay. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5726.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5727.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5728.jpg) Once that was done, we allowed it to dry for roughly 24 hours. tick… tock… tick… tock… And we’re back!! Now it was time to do exactly the same process to [the other side](https://www.gbfans.com/wiki/publications/comics/ghostbusters-the-other-side), but 1st we had to remove the clay wall that was built on top of the rubber. We then rubbered a generous amount of vaseline on the seam where we took the clay from. This helps to keep the two halfs from forming as one and allows it to come apart easilywhich is what we were aiming for. Once that was dry it was time to crack this baby open…oh what a job we had at doing that!!! 1st we decided to grind off the flash/jaggy bits from the seam to stop from getting cut. Then using a hammer and screwdriver just tap into the seam all along the length of it. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5791.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5802.jpg) ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [August 11, 2011, 3:47pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/11 "2011-08-11T15:47:37Z")
The next part was a bit of an effort/struggle and very time consuming as it took 3 of us to prise it open and roughly 1 hour. I’ll let the next set of pics speak for themselves. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5804.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5806.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5808.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5809.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5810.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5811.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5813.jpg) And now we have our mould, ready for making the fibreglass shell which I’ll cover in my next instalment. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF5814.jpg) ---
**Author:** ![chibigear](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/c/65b543/32.png) [@chibigear](https://forum.gbfans.com/u/chibigear)\ **Post date:** [August 11, 2011, 4:45pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/12 "2011-08-11T16:45:58Z")
NICE!!! ---
**Author:** ![Croesus](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/c/e47c2d/32.png) [@Croesus](https://forum.gbfans.com/u/Croesus)\ **Post date:** [August 12, 2011, 1:37pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/13 "2011-08-12T13:37:20Z")
that sir… requires a belly clap very cool ---
**Author:** ![Filandrius](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/f/839c29/32.png) [@Filandrius](https://forum.gbfans.com/u/Filandrius)\ **Post date:** [August 12, 2011, 2:15pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/14 "2011-08-12T14:15:29Z")
I thoroughly admire anybody who has the skill and courage to embark on such an endeavour. Good job sir. :crunch: ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [August 12, 2011, 3:16pm UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/15 "2011-08-12T15:16:45Z")
Cheers folks, really appreciate all the comments. I dunno about skill and courage, but i for me it’s all about the hobby side of things, and building things i love to attempt…so long as i can do it for cheaper or the same price of course. But yeah i reckon everybody should take a stab at buildin something, it gives ya a great feeling of knowing you’ve done it and build something from a few scrap pieces of wood, or even built a resin kit etc… ---
**Author:** ![nick-a-tron](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/n/fbc32d/32.png) [@nick-a-tron](https://forum.gbfans.com/u/nick-a-tron)\ **Post date:** [August 13, 2011, 12:33am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/16 "2011-08-13T00:33:49Z")
Thats a great looking mould! Nice job. ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [September 9, 2011, 12:31am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/17 "2011-09-09T00:31:54Z")
So the wait is finally over and i have the 1st fiberglass shell out of the mould!! It took alot of time, sweat, tears and hoping & praying it would come out looking half decent or it was ALOT of money’s worth down the drain. I don’t have any pics of the actual moulding process seeing as my hands were full of resin and fiberglass matting, but we got it out and it looked pretty good for a 1st attempt. A few bits needed seeing to with a touch of fillers and sanding, but other than that it looked fine. One that was done it was time to fake weld the [N-Filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter) with hot glue. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6086.jpg) Once that was done, we shot it with a full tin of undercoat, just to see wut it would show up. Again, everything looks pretty good. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6087.jpg) ---
**Author:** ![parksdesign](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/p/77aa72/32.png) [@parksdesign](https://forum.gbfans.com/u/parksdesign)\ **Post date:** [September 10, 2011, 3:33am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/18 "2011-09-10T03:33:30Z")
Looks great. ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [September 21, 2011, 2:45am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/19 "2011-09-21T02:45:43Z")
So with the pack primed and everything looking good, it was time to get cracking on preparing the shell for all the extra’s that have to be screwed, glued and fixed onto it. First move was to drill out the holes on the Powercell and [Cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron). ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6203.jpg) One the were sorted we flipped the shell over and carved out indents on the Cyclotron and Powercell for the lenses to be able to sit in tight against the shell. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6210.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6213.jpg) Next it was time to pay some atention to the resin that will be attached to the shell. For the HGA and [Ion Arm](https://www.gbfans.com/shop/aluminum-welded-ion-arm) i had to bake 2 wooden bungs to glue to the inside to allow me to be able to affix these to the shell. Once cut out i drilled a hole in the middle and glued a bolt into place ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6214.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6222.jpg) I then hot glued some fake weld onto the Ion Arm after drilling out all the holes for the Resistors and [Legris](https://www.gbfans.com/wiki/equipment/proton-pack/legris) Elbow. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6224.jpg) For the PPD all i had to do was drill a hole to allow the tubing and split loom into it. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6216.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6219.jpg) For the [Injectors](https://www.gbfans.com/wiki/equipment/proton-pack/injectors) i did the same as the HGA and Ion Arm with the wooden bungs on both ends. For these i made them out of 2 lengths on Aluminium pipe. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6229.jpg) For the bottom of the Injectors (the ends that are not directly screwed into the Shell) I slightly recessed the wooden bungs and covered them in Isopon fillers. After that i drilled a hole in the middle for the Hose Barb to fit into, and then i fake welded the bottoms with some more hot glue. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6234.jpg) ---
**Author:** ![Warrenzo](https://forum.gbfans.com/user_avatar/forum.gbfans.com/warrenzo/32/5853_2.png) [@Warrenzo](https://forum.gbfans.com/u/Warrenzo)\ **Post date:** [September 21, 2011, 2:46am UTC](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920/20 "2011-09-21T02:46:22Z")
I then undercoated each of the bits and gave them 2 coats of silver…shown here is the [Ion Arm](https://www.gbfans.com/shop/aluminum-welded-ion-arm), Boster Frame, HGA (with the holes drilled), [Crank Knob](https://www.gbfans.com/shop/crank-knob) (Left grey for accuracy), [Booster Tube](https://www.gbfans.com/wiki/equipment/proton-pack/booster-tube), Booster Tube Plug and [Bumper](https://www.gbfans.com/wiki/equipment/proton-pack/bumper). ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6227.jpg) With these left to dry i turned my attention back to the shell and decided to drill out all the holes on the [N-Filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter), for mounting the shell to the [Motherboard](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard), straights, split loom hosing, [Legris](https://www.gbfans.com/wiki/equipment/proton-pack/legris) Elbow, Gun Mount, [Ribbon cable](https://www.gbfans.com/wiki/equipment/proton-pack/ribbon-cable), [Ribbon cable clamp](https://www.gbfans.com/shop/ribbon-cable-clamp) and for attaching the resin parts. I also glued the PPD to the EDA. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6242.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6244.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6245.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6246.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6248.jpg) ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6249.jpg) Once all the nessacery holes were drilled it was time to colour it in with silver paint…man it looks sweet in silver lol!! ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6250.jpg) Again it was time to wait on the paint drying so i decided to glue the Hose Barbs in the [Injectors](https://www.gbfans.com/wiki/equipment/proton-pack/injectors), the Booster Tube plug into the Booster Tube and spray everything satin black. You can see that i have also included the L Bracket which attaches to the Injectors in this pic. ![image]([http://www.gbfans.com/images/pb/warrenzo/Ghostbusters](http://www.gbfans.com/images/pb/warrenzo/Ghostbusters) Proton Pack\_DSCF6241.jpg) [Next page](https://forum.gbfans.com/t/my-gb1-style-proton-pack-thrower/36920.md?page=2)