# Putting a Hyperdyne kit into a GuntahKela PKE shell Tutorial

**URL:** <https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685>\
**Category:** PKE Meters\
**Created:** [October 20, 2009, 7:20am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685 "2009-10-20T07:20:50Z")\
**Posts on this page:** 20\
**Page:** 2

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 28, 2009, 5:35pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/21 "2009-10-28T17:35:16Z")

</div>

Okay, tutorial time!

First off, if you buy the deluxe kit, uncut wing boards, and a couple of servos, here’s what you get:

 ![image](https://discdn.gbfans.com/original/3X/d/c/dc3df9eb777d4603a56b9940318eb7bf2ed00530.jpeg)

First order of business is to get the wings shaped, since they come like this:

 ![image](https://discdn.gbfans.com/original/3X/0/0/005ed3ad6607a5f5a3d8a5476c51f7e3efdee6d8.jpeg)

I used my dremel cutting wheel to separate them, then used the grinding wheel to shape them. Here’s them cut apart, with some shaping already done to the top one.

 ![image](https://discdn.gbfans.com/original/3X/c/1/c173eef0f077f155f36225d82a0a4da5ac24e991.jpeg)

The wings are outlined with trace, try to remove all of the outline trace without hitting the actual wiring traces. The boards are pretty tough and don;t just melt away on the grinding wheel, so it’s actually not that hard to get this done. If you have any of the outline trace, just scrape it up with the tip of an exacto or similar. You don’t have to worry too much about the bottom outline, but you DEFINITELY want to clear off the top outline, since the LEDs could bump against it and short. Then solder the LEDs to the boards, making sure the polarity is correct. Teh positive side will always sit on the side closest to the PKE body.

 ![image](https://discdn.gbfans.com/original/3X/0/7/0786f6faeb92213d1bdfaa3ab4bd41365e3b0a4c.jpeg)

(Sorry for the yellow, the flash washed everything out when I used it)

Now for some reason, a few of my pics got corrupted on the card, so I’m missing my own pics for a couple of steps. However, the instructions that come with the kit are quite helpful. The next order of business is to wire the [ribbon cables](https://www.gbfans.com/wiki/equipment/proton-pack/ribbon-cable) to the wing boards, and let me just say to wire them up EXACTLY the way you see them in the picture in the .PDF instructions. (See my previous post for my adventure. I got it fixed properly, but I wired them up incorrectly the first time and cost myself an extra 3-4 hours of work cleaning up and rewiring the PCBs.)

After that it’s simply a matter of assembing the shell. This will vary for person to person; some may find their servos fit without any modification to the inner shell, some of you may have to clean out a bit of the casting to have your servos fit flush. Just take your time and constantly check your fit and you’ll be fine.

Here’s a quick shot of the inside of mine:

 ![image](https://discdn.gbfans.com/original/3X/9/3/9365287da622bb5a25f26c17fc599b97b6de5384.jpeg)

The only thing glued into place are the servos, the on/off switch, and the scrap bits of wood I used in the handle and at the top of the PKE so I could screw the halves together. The board itself is held in place but a length of bamboo skewer wedged under the ridges on the front half of the PKE. Holds everything in place quite handily, and makes it easy to remove if I ever need to. The battery is just duct taped into the body cavity.

And as seen earlier, here’s a video of the finished PKE:

> **[\- YouTube](https://www.youtube.com/v/TifBzCz8s7E)**
>
> Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.

(Anyone know how to get the YouTube embedding to work?)

Good luck!

---

<div class="post-metadata">

**Author:** ![ChexGuy331](https://forum.gbfans.com/user_avatar/forum.gbfans.com/chexguy331/32/3995_2.png) [@ChexGuy331](https://forum.gbfans.com/u/ChexGuy331)\
**Post date:** [October 28, 2009, 7:27pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/22 "2009-10-28T19:27:32Z")

</div>

That looks very nice. Where would I get the shell (not that I plan to do this because I have no money)?

And I noticed a loud whirring noise when the wings were fully closed in the video…it’s not supposed to do that, is it?

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 28, 2009, 9:32pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/23 "2009-10-28T21:32:08Z")

</div>

> [@ChexGuy331](#):
>
> That looks very nice. Where would I get the shell (not that I plan to do this because I have no money)?
> 
> And I noticed a loud whirring noise when the wings were fully closed in the video…it’s not supposed to do that, is it?

It’s just the servos trying to close the wings further than they fit, my fault for setting them in too far. It’s not an issue.

---

<div class="post-metadata">

**Author:** ![gunza](https://forum.gbfans.com/user_avatar/forum.gbfans.com/gunza/32/5928_2.png) [@gunza](https://forum.gbfans.com/u/gunza)\
**Post date:** [October 28, 2009, 10:06pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/24 "2009-10-28T22:06:50Z")

</div>

you need to use [.youtube]XXX[./youtube] XXX=TifBzCz8s7E ([http://www.youtube.com/v/](http://www.youtube.com/v/) **TifBzCz8s7E** ) Just remove the periods…

[https://www.youtube.com/watch?v=TifBzCz8s7E](https://www.youtube.com/watch?v=TifBzCz8s7E)

question…does it cost less to cut the wings yourself, or is that just how it comes?

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 29, 2009, 12:03am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/25 "2009-10-29T00:03:08Z")

</div>

> [@gunza](#):
>
> you need to use [.youtube]XXX[./youtube] XXX=TifBzCz8s7E ([http://www.youtube.com/v/](http://www.youtube.com/v/) **TifBzCz8s7E** ) Just remove the periods…
> 
> [https://www.youtube.com/watch?v=TifBzCz8s7E](https://www.youtube.com/watch?v=TifBzCz8s7E)
> 
> question…does it cost less to cut the wings yourself, or is that just how it comes?

It’s cheaper. Sometimes Hyperdyne offers the wings fully cut and assembled, and there’s a pre-assembled kit that you can basically just plug into your PKE shell and go. I went with the uncut/unassembled wings since that’s all he was going to have available in time for Satruday.

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 29, 2009, 12:05am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/26 "2009-10-29T00:05:42Z")

</div>

> [@ChexGuy331](#):
>
> That looks very nice. Where would I get the shell (not that I plan to do this because I have no money)?
> 
> And I noticed a loud whirring noise when the wings were fully closed in the video…it’s not supposed to do that, is it?

Oh, and the shell is one of GuntahKela’s. Definitely worth nabbing.

---

<div class="post-metadata">

**Author:** ![ChexGuy331](https://forum.gbfans.com/user_avatar/forum.gbfans.com/chexguy331/32/3995_2.png) [@ChexGuy331](https://forum.gbfans.com/u/ChexGuy331)\
**Post date:** [October 29, 2009, 12:52am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/27 "2009-10-29T00:52:35Z")

</div>

Aww, he’s not selling any right now.

Well, I don’t have any money anyway. 😛

Parent’s probably wouldn’t let me spend it on a kit either.

---

<div class="post-metadata">

**Author:** ![Cornelius](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/c/e19adc/32.png) [@Cornelius](https://forum.gbfans.com/u/Cornelius)\
**Post date:** [October 29, 2009, 8:25am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/28 "2009-10-29T08:25:28Z")

</div>

Peaugh,

Could you perhaps take a few more detailed pictures of how you put all the inner parts (wires/servo’s/boards/what-have-you) into both shells? It’s great already to see the pictures you posted in this thread, but it would give _even so much more_ useful information!

I love your PKE, by the way!

CK

---

<div class="post-metadata">

**Author:** ![aj-quick](https://forum.gbfans.com/user_avatar/forum.gbfans.com/aj-quick/32/188008_2.png) [@aj-quick](https://forum.gbfans.com/u/aj-quick)\
**Post date:** [October 29, 2009, 6:25pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/29 "2009-10-29T18:25:26Z")

</div>

I got my Hyperdyne Labs kit today! That was quick!

I noticed that mine is a little different from yours as it uses new smaller chips or something. My main question is.. how do the circuit boards fit into the wings? I didn’t get those.. but would you recommend them?

All I got with my kit was some wire and no LEDs.. so I’m wondering which would be the best method? Circuit Board wings or just wires running through the wings?

Also.. one thing I noticed is that the speaker is annoying! Did you think about covering it up a little bit so it isn’t as loud?

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 29, 2009, 6:58pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/30 "2009-10-29T18:58:54Z")

</div>

> [@AJ Quick](#):
>
> I got my Hyperdyne Labs kit today! That was quick!
> 
> I noticed that mine is a little different from yours as it uses new smaller chips or something. My main question is.. how do the circuit boards fit into the wings? I didn’t get those.. but would you recommend them?
> 
> All I got with my kit was some wire and no LEDs.. so I’m wondering which would be the best method? Circuit Board wings or just wires running through the wings?
> 
> Also.. one thing I noticed is that the speaker is annoying! Did you think about covering it up a little bit so it isn’t as loud?

Once you shape the circuit boards, just test fit them into the wing halves. I had to clear a little material our of the inside of the wings to make them fit, but not much, and then you just epoxy the wing halves together around the boards. Easy peasy.

As for method, either one (circuit boards or wires) should work fine, there’s enough room in the wings to just run wires if you wish.

As for the speaker, I find it’s not nearly so annoying once you have it encased in the shell, but you could certainly put a piece of duct or electrical tape over it to muffle it if you wish.

Cornelius - I’ll see what I can do about retaking some of those pics for you.

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 29, 2009, 7:40pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/31 "2009-10-29T19:40:52Z")

</div>

For those that wanted more pics:

Here’s a shot of the back, I just cut a hole for the power switch in the back of the handle. Not super pretty, but it’s hidden in your hand while holding the PKE and makes turning it on/off a snap.

 ![image](https://discdn.gbfans.com/original/3X/4/2/42789977284c5ae323ba2d52718dcec9aa15ac21.jpeg)

And the circuit board itself. I just used my fingers/tweezers to slot the LEDS into the front face, then just set the circuit board in and then used a length of bamboo skewer under the side ridges to hold it in place. It’s actually VERY solid, and makes things easy to remove if needed.

 ![image](https://discdn.gbfans.com/original/3X/b/c/bccb7ad73be49a29c2accfb0be12e9fa5a7461dc.jpeg)

And here’s [the other side](https://www.gbfans.com/wiki/publications/comics/ghostbusters-the-other-side). You can see the scrap wood I glued into the top half of the front for the shell screws. The servos are glued onto the sides of the shell, and you can see some white where I had to clear away a little of the molding inside to have the servos sit level. Also, you can see where the 9v battery is just ducttaped in. I considered hiding it in the handle, but there was JUST not enough space, and by that point I was getting tired of dremeling the inside and just taped it in place. Still, it adds a little weight to the main chamber as if it were actually stuffed full of electronics and makes it easy to swap out, so no worries.

 ![image](https://discdn.gbfans.com/original/3X/6/2/62e652eeb382fefed7734c51962f5c0c71990be1.jpeg)

This is just a different angle on the insides. The only things glued in are the servos themselves, the power switch, and the scrap wood. You can easily pop everything out if you need to work on anything. Some people glue the wings onto the servos, but I found that with guntahkela’s wings being molded to hold the crossbar inside, I just glued that into the wing itself but didn’t glue it onto the servo directly. They hold just fine and also pop off easily if any wires come loose and need to be resoldered in the future.

 ![image](https://discdn.gbfans.com/original/3X/b/a/ba1cf8a41786c7b2c9c4e96642cf1ecec6dafec6.jpeg)

And a still shot of the finished PKE:

 ![image](https://discdn.gbfans.com/original/3X/0/2/0246f809244a2680647522e1541ee2a43b3d1076.jpeg)

---

<div class="post-metadata">

**Author:** ![exo95er](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/e/e47774/32.png) [@exo95er](https://forum.gbfans.com/u/exo95er)\
**Post date:** [October 29, 2009, 8:54pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/32 "2009-10-29T20:54:47Z")

</div>

Peaugh, thank you for posting. Yeah, it’s pretty tight in there, especially with those servos!

You’re in an inspiration for us all! 🆒

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 30, 2009, 4:36am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/33 "2009-10-30T04:36:51Z")

</div>

> [@exo95er](#):
>
> Peaugh, thank you for posting. Yeah, it’s pretty tight in there, especially with those servos!
> 
> You’re in an inspiration for us all! 🆒

Yeah, it gets pretty tight, but there’s still enough room for everything to move.

---

<div class="post-metadata">

**Author:** ![Cornelius](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/c/e19adc/32.png) [@Cornelius](https://forum.gbfans.com/u/Cornelius)\
**Post date:** [October 30, 2009, 8:35am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/34 "2009-10-30T08:35:10Z")

</div>

Some very illuminating pictures indeed! Peaugh, thanks a million! This actually makes me reconsider purchasing a Hyperdyne kit after all…

CK

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 30, 2009, 5:22pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/35 "2009-10-30T17:22:25Z")

</div>

> [@Cornelius](#):
>
> Some very illuminating pictures indeed! Peaugh, thanks a million! This actually makes me reconsider purchasing a Hyperdyne kit after all…
> 
> CK

I didn’t turn you off of one, did I? It’s a good kit.

---

<div class="post-metadata">

**Author:** ![ChexGuy331](https://forum.gbfans.com/user_avatar/forum.gbfans.com/chexguy331/32/3995_2.png) [@ChexGuy331](https://forum.gbfans.com/u/ChexGuy331)\
**Post date:** [October 30, 2009, 6:17pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/36 "2009-10-30T18:17:46Z")

</div>

I think he’s saying you made him change his mind about NOT buying the Hyperdyne kit.

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [October 30, 2009, 11:34pm UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/37 "2009-10-30T23:34:11Z")

</div>

> [@ChexGuy331](#):
>
> I think he’s saying you made him change his mind about NOT buying the Hyperdyne kit.

Yeah, that would make more sense.

---

<div class="post-metadata">

**Author:** ![Cornelius](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/c/e19adc/32.png) [@Cornelius](https://forum.gbfans.com/u/Cornelius)\
**Post date:** [October 31, 2009, 9:39am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/38 "2009-10-31T09:39:19Z")

</div>

I guess I forgot the word ‘not’. Oh well, I have an excuse: I’m not a native speaker! (but then again, I teach English; I guess I had better quit my job).

---

<div class="post-metadata">

**Author:** ![Peaugh](https://forum.gbfans.com/user_avatar/forum.gbfans.com/peaugh/32/6114_2.png) [@Peaugh](https://forum.gbfans.com/u/Peaugh)\
**Post date:** [November 9, 2009, 6:19am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/39 "2009-11-09T06:19:08Z")

</div>

> [@Cornelius](#):
>
> I guess I forgot the word ‘not’. Oh well, I have an excuse: I’m not a native speaker! (but then again, I teach English; I guess I had better quit my job).

No, it’s cool, I figured as much, just wanted to make sure I hadn’t dissuaded anyone away from the PKE kit. It’s a good solid kit and looks great when finished.

How’s everyone else coming on their PKEs? I’m curious, and I like watching all of this stuff come together.

---

<div class="post-metadata">

**Author:** ![aj-quick](https://forum.gbfans.com/user_avatar/forum.gbfans.com/aj-quick/32/188008_2.png) [@aj-quick](https://forum.gbfans.com/u/aj-quick)\
**Post date:** [November 9, 2009, 7:04am UTC](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685/40 "2009-11-09T07:04:32Z")

</div>

Haven’t bought servos yet.

[Previous page](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685.md?page=1)

[Next page](https://forum.gbfans.com/t/putting-a-hyperdyne-kit-into-a-guntahkela-pke-shell-tutorial/14685.md?page=3)
