# Question about TC’s v3 Trigger Box

**URL:** <https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908>\
**Category:** Proton Packs\
**Created:** [August 2, 2019, 9:54pm UTC](https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908 "2019-08-02T21:54:09Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![alleyradb](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/a/65b543/32.png) [@alleyradb](https://forum.gbfans.com/u/alleyradb)\
**Post date:** [August 2, 2019, 9:54pm UTC](https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908/1 "2019-08-02T21:54:09Z")

</div>

Hey everyone,

I’ve started a new wand build and purchased it from TC. I’ve read his build threads and viewed his videos but I can’t quite find the “correct” answer on how to secure the [trigger box](https://www.gbfans.com/wiki/equipment/proton-pack/trigger-box) to the rear [instrument bar](https://www.gbfans.com/wiki/equipment/proton-pack/instrument-bar). I did message TC but haven’t heard back.

The new trigger box doesn’t have a stand-off or build in pegs to screw into. However it does look like it has drill markings for a set screw. I figured I’d ask the community, specifically those who’ve recently purchased his wand kit.

Thanks!

---

<div class="post-metadata">

**Author:** ![JWils23](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/j/bcef8e/32.png) [@JWils23](https://forum.gbfans.com/u/JWils23)\
**Post date:** [August 3, 2019, 1:21am UTC](https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908/2 "2019-08-03T01:21:46Z")

</div>

I had the same issue with mine, I think the old throwers had a screw attaching but the new ones do not. It’s hard to tell from the picture but yours appears to be the same as mine. On the inside of the [trigger box](https://www.gbfans.com/wiki/equipment/proton-pack/trigger-box) there should be two indents and on the piece that you connect it to there should be two lumps. It should click together, though mine was a little loose. What I did was take some gaffers tape (you could use any tape really) and cut a thin line that I wrapped around the piece which is connected to the thrower body. This really helped snug everything up and I’ve never had an issue with them separating since then. Hopefully I explained that well enough and it makes sense. But I’m sure you could also drill a hole on the underside for a small set screw as well if you wanted to.

---

<div class="post-metadata">

**Author:** ![alleyradb](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/a/65b543/32.png) [@alleyradb](https://forum.gbfans.com/u/alleyradb)\
**Post date:** [August 3, 2019, 1:25am UTC](https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908/3 "2019-08-03T01:25:57Z")

</div>

Makes perfect sense!

I just assumed using set screws so if any maintenance needed to be done, it could be. I don’t want that box sealed shut permanently — I went a little wild with the gorilla glue on my first wand and immediately regretted it when I needed to adjust something. But I also want to build it the “correct” way, while trying to make it as accurate as possible.

---

<div class="post-metadata">

**Author:** ![JWils23](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/j/bcef8e/32.png) [@JWils23](https://forum.gbfans.com/u/JWils23)\
**Post date:** [August 3, 2019, 3:01am UTC](https://forum.gbfans.com/t/question-about-tc-s-v3-trigger-box/4908/4 "2019-08-03T03:01:27Z")

</div>

I was in the same boat, and using the tape was a perfect compromise for me. I can pop the [trigger box](https://www.gbfans.com/wiki/equipment/proton-pack/trigger-box) on and off easily without needing tools, but at the same time it’s secure enough that it won’t fall off. But using a little set screw would also work great, just depends on which route you want to go!
