# Random Pack Questions: Asking as I build

**URL:** <https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546>\
**Category:** Proton Packs\
**Created:** [November 2, 2026, 10:10pm UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546 "2026-11-02T22:10:18Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![imperialwalker](https://forum.gbfans.com/user_avatar/forum.gbfans.com/imperialwalker/32/188109_2.png) [@imperialwalker](https://forum.gbfans.com/u/imperialwalker)\
**Post date:** [November 2, 2026, 10:10pm UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/1 "2026-11-02T22:10:18Z")

</div>

Hey,

I’ve started to slowly build a pack and I wanted to start a thread for all the questions I have. I’m sorry if they’ve been asked a million times. I’ve done my best to search the answers before posting to not be repetitive.

1. Is there a reason the [Filler Plug](https://www.gbfans.com/wiki/uncategorized/filler-plug) and Beamline have only one screw/bolt holding them on? Do they not rotate after a while?

2. Are the tubes (Filler Plug, Beamline, [Injectors](https://www.gbfans.com/wiki/equipment/proton-pack/injectors), etc) standard tube sizes? Can they be created from PVC tubes accurately to avoid 3D printing?

---

<div class="post-metadata">

**Author:** ![spooky](https://forum.gbfans.com/user_avatar/forum.gbfans.com/spooky/32/188552_2.png) [@spooky](https://forum.gbfans.com/u/spooky)\
**Post date:** [November 3, 2026, 12:45am UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/2 "2026-11-03T00:45:41Z")

</div>

I believe both [filler tubes](https://www.gbfans.com/wiki/equipment/proton-pack/filler-tubes) are 1.25 OD

---

<div class="post-metadata">

**Author:** ![imperialwalker](https://forum.gbfans.com/user_avatar/forum.gbfans.com/imperialwalker/32/188109_2.png) [@imperialwalker](https://forum.gbfans.com/u/imperialwalker)\
**Post date:** [November 3, 2026, 8:09am UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/3 "2026-11-03T08:09:40Z")

</div>

Question about the Q-Pack (if you’ve built one).

When putting together the pack with the mostly M3 screws, did you find any issues with the assembly such as screwing directly into plastic, hardware interfering with cables, or any other issues you wish were different?

I am remixing some of the parts to allow for cutouts for nuts and I am looking for thoughts and experiences.

---

<div class="post-metadata">

**Author:** ![zeta-otaku](https://forum.gbfans.com/user_avatar/forum.gbfans.com/zeta-otaku/32/186411_2.png) [@zeta-otaku](https://forum.gbfans.com/u/zeta-otaku)\
**Post date:** [November 3, 2026, 1:22pm UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/4 "2026-11-03T13:22:00Z")

</div>

I’ve built a couple Q packs and just screwed directly into the 3D printed parts.

---

<div class="post-metadata">

**Author:** ![onedge](https://forum.gbfans.com/user_avatar/forum.gbfans.com/onedge/32/188280_2.png) [@onedge](https://forum.gbfans.com/u/onedge)\
**Post date:** [November 3, 2026, 2:56pm UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/5 "2026-11-03T14:56:17Z")

</div>

The [Filler Plug](https://www.gbfans.com/wiki/uncategorized/filler-plug) and Beamline really only have one screw because its not load bearing anything, so its not going to rotate after a while unless somebody is actively trying to mess it up.

The Filler Plug and Beamline have a 1-1/8 inch diameter and can be found as 1 inch ID PEX tubing. The [Injector](https://www.gbfans.com/wiki/equipment/proton-pack/injectors) tube’s diameter is around 1-1/2 inches (It seems that it’s a little unclear at times) and it can probably be sourced from ABS pipe at your hardware store. The [Booster tube](https://www.gbfans.com/wiki/equipment/proton-pack/booster-tube) and HGA have a diameter of 2-1/2 inches while the [N-Filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter) has a diameter of 3 inches. Unfortunately 2-1/2 inch outer diameter piping is not standard for PVC, but it does come in an outer diameter of 2-3/8 which is close and matches Stefan Otto’s plans (works if you seriously want to avoid 3D printing). You might also have trouble trying to find a pipe that has the proper diameter for the N-Filter too.

I would recommend for most of the tubing to take a measuring tape to a hardware store to see if they have pipes that are the correct diameter.

---

<div class="post-metadata">

**Author:** ![imperialwalker](https://forum.gbfans.com/user_avatar/forum.gbfans.com/imperialwalker/32/188109_2.png) [@imperialwalker](https://forum.gbfans.com/u/imperialwalker)\
**Post date:** [November 7, 2026, 10:21pm UTC](https://forum.gbfans.com/t/random-pack-questions-asking-as-i-build/219546/6 "2026-11-07T22:21:20Z")

</div>

On the Q-Pack, the [Injector](https://www.gbfans.com/wiki/equipment/proton-pack/injectors) Block appears to be offset (not centred in the block on the SyncGen). This results in the [Motherboard](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard) having a large lip on the bottom side. Is this by design? I looked at the reference and to my eyes the Injector Block seems centred.

 ![Screenshot 2026-11-07 at 3.20.52 PM](https://discdn.gbfans.com/original/3X/1/a/1ac5e44c1de6c7af4d59ab557c813e7b9df83fd3.png)
