# RGB Spirit Project **URL:** \ **Category:** Proton Packs\ **Created:** [November 4, 2018, 7:25pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689 "2018-11-04T19:25:34Z")\ **Posts on this page:** 16\ **Page:** 1
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 4, 2018, 7:25pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/1 "2018-11-04T19:25:34Z")
I nabbed a new pack, and trap 50% off Thursday. Thought I would start a thread to hold myself accountable to progress, and bug you all for advice. long winds ahead… Ive seen a couple of people just paint up the pack in toon colors but, I am not a fan. I’m well aware that I won’t get a 100% accuracy but, I would like something similar. Any help you have would be greatly appreciated. First draft of ideas are: 1. New thrower I cannot find a project box that I would like to use for the main body. Based on my quick measurements, the box where the wand mounts is 3.5 x 3.5-4in. I have to account for the side rails to slide over the box. I have searched everywhere and haven’t found any vague dimensions to scale this to. Ill probably just use a V-clip. I dont really want to scratch build a box. 1. Replace booster with red PVC, use a small funnel, and run a tube over the existing fitting where the big green tube goes. The top part of the booster screws off but, the frame is still moulded into the body. I had thought about just painting that red but, I want to replace the top part with a box. I could possibly cut out some PVC pipe, and fit it over but, the PPD would be in the way. I might even keep the PPD and run the funnel under it. I could also cut out the frame. 1. Remove Clippard on pack. Repace with arcade button. Enough said. 1. Mounts for the trap The trap at full size, is huge in relation to this pack. Ill get this pack finished before I dive off into that massive project. 1. Cut out a piece of PVC to cover the box with the big “Warning” label over it. Obviously in banana yellow. seems easy enough. 1. Remove crank on generator. Replace with voltage meter (if I can find one proportionate) If anyone knows of a small one, point me to it. 1. Make [Ion Arm](https://www.gbfans.com/shop/aluminum-welded-ion-arm) bigger, width wise. Replacing where the top of the booster screws off with a box. I figure I can find an electrical box at lowes to do this, epoxy it to the arm, and hide the evidence with Bondo. 1. I want to figure something out about the bottom half of the [Cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron). I currently have no solutions. Ill keep a bunch of the pack as, I don’t want to ruin the structure of it. The V2 seems a bit inferior to the first version I have. I like that most of the fittings are screwed in, without being murdered by poorly applied superglue. The [injectors](https://www.gbfans.com/wiki/equipment/proton-pack/injectors) will stay, I will remove the top half of the [N-filter](https://www.gbfans.com/wiki/equipment/proton-pack/n-filter), [ribbon cable](https://www.gbfans.com/wiki/equipment/proton-pack/ribbon-cable) will go, and I think the HGA might stay or, be covered. I also be using an aluminum [motherboard](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard). Keeping the existing straps is fine but, ill be adding a seatbelt for the waist. A huge relief from having to mount the thing to an ALICE. Stay tuned! ---
**Author:** ![ghostengineer](https://forum.gbfans.com/user_avatar/forum.gbfans.com/ghostengineer/32/178888_2.png) [@ghostengineer](https://forum.gbfans.com/u/ghostengineer)\ **Post date:** [November 4, 2018, 8:17pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/2 "2018-11-04T20:17:37Z")
Hi there I have a spare spirit pack that I have thought about painting into RGB colors for the hell of it and I have toyed with the idea of maybe getting a [Kenner](https://www.gbfans.com/wiki/real-ghostbusters/kenner-10410) wand and using that with the spirit pack and then adding the carrot on the stick at the end of the wand. That was an idea I floated around in my head for some time. Would be fun to do regardless of which direction I go. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 5, 2018, 1:50am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/3 "2018-11-05T01:50:13Z")
> [@ghostengineer post\_id=4910463 time=1541362657 user\_id=37027](#): > > Hi there I have a spare spirit pack that I have thought about painting into RGB colora for the hell of it and I have totes with the idea of maybe getting a Kenner wand and using that with the spirit pack and then adding the carrot on the stick at the end of the wand. That was an idea I floated around in my head for some time. Would be fun to do regardless of which direction I go. I thought about using the [Kenner](https://www.gbfans.com/wiki/real-ghostbusters/kenner-10410) stuff, too. The cost of the wand, and trap put me off, though. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 6, 2018, 3:48pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/4 "2018-11-06T15:48:00Z")
Started working on a wand. Ended up with a box from Home Depot that’s 5.8x2.5x3 (rounded up). It’s too tall so, I’m gonna hit it up with my big sander. Using a metal cover plate on the bottom. Length so far: 21in Cost: $13 ![image](http://i63.tinypic.com/290quq8.jpg) I hope to find some more rigid small PVC for the tube that connects to the tip. The stuff at HD was too soft. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 14, 2018, 3:11am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/5 "2018-11-14T03:11:41Z")
My progress slowed a bit. I have some BUD aluminum boxes coming Thursday THEN, I’ll finally start to work on the pack itself. I couldnt find an appropriate switch for my wand. Settled on an ON/OFF that I had from Walmart. Its Red/Amber. It will do. I might paint it. The cheapest blow gun tip that was a good size was $11 so, I built my own from a $2 1/4 harbor freight tip, and a bottle cap. I have knobs, button and lights coming from China. Nothing is glued together… just a mockup: ![image](http://i65.tinypic.com/2yv71cn.jpg) Anyone have experience with Plastidip spray paint? I’m pondering moulding the grips from epoxy, and coating them in that. I had planned on cutting the side plates for the gun box from aluminum but, I have no clue if it want 1/8 or, 1/4". I would have a hard time getting good bands with 1/4. ---
**Author:** ![Heatley2001](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/b3f665/32.png) [@Heatley2001](https://forum.gbfans.com/u/Heatley2001)\ **Post date:** [November 14, 2018, 8:03pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/6 "2018-11-14T20:03:02Z")
im looking forward to seeing how this turns out. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 16, 2018, 1:53am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/7 "2018-11-16T01:53:19Z")
Another 1/4" and this would be perfect. ![image](http://i68.tinypic.com/117wmjn.jpg) ![image](http://i63.tinypic.com/2hqax61.jpg) ---
**Author:** ![DarkSpectre](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/d/958977/32.png) [@DarkSpectre](https://forum.gbfans.com/u/DarkSpectre)\ **Post date:** [November 16, 2018, 3:50pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/8 "2018-11-16T15:50:01Z")
I’m really interested to see where this goes! ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 17, 2018, 10:06pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/9 "2018-11-17T22:06:26Z")
Made a spacer. Not going to remove much more from the body. This thing got real flimsy when I started cutting into it. I talked to my mother, and her new job has a plasma cutter. Hoping to get my thrower sides and [motherboard](https://www.gbfans.com/wiki/equipment/proton-pack/motherboard) cut there for cheaps. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 20, 2018, 12:32am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/10 "2018-11-20T00:32:44Z")
I guess I’m gonna try it. Having a four light [cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron) would bug me forever. Probably going to be more trouble than it’s worth to cut to fit. ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [November 23, 2018, 8:38pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/11 "2018-11-23T20:38:19Z")
The [cyclotron](https://www.gbfans.com/wiki/equipment/proton-pack/cyclotron) was a failure. I didnt want to spend $9 on PVC so, I made the yellow tank, and cleaned out my pantry at the same time. Made from a Peanut Butter lid, plastic bottle, and a “no trespassing” sign. Going to coat it in bondo. Cut to fit. ---
**Author:** ![Mikv](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/m/4bbf92/32.png) [@Mikv](https://forum.gbfans.com/u/Mikv)\ **Post date:** [December 12, 2018, 11:16am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/12 "2018-12-12T11:16:30Z")
Awesome project! Any news? I’m very curious 😃 ---
**Author:** ![hutto](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/h/f9ae1b/32.png) [@hutto](https://forum.gbfans.com/u/hutto)\ **Post date:** [December 23, 2018, 6:08am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/13 "2018-12-23T06:08:16Z")
> [@Mikv post\_id=4911318 time=1544613390 user\_id=1210](#): > > Awesome project! > > Any news? > > I’m very curious 😃 Thanks and, nope. Weather wasn’t great for painting for a while and, my arcade button never showed up. Still gotta Bondo. I plan on hitting it back up Tuesday. I’m about to order a button on Amazon. ---
**Author:** ![ghostengineer](https://forum.gbfans.com/user_avatar/forum.gbfans.com/ghostengineer/32/178888_2.png) [@ghostengineer](https://forum.gbfans.com/u/ghostengineer)\ **Post date:** [January 28, 2019, 11:44pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/14 "2019-01-28T23:44:48Z")
Any progress with this? Would love to see more ---
**Author:** ![3mandos](https://forum.gbfans.com/letter_avatar_proxy/v4/letter/3/fbc32d/32.png) [@3mandos](https://forum.gbfans.com/u/3mandos)\ **Post date:** [February 15, 2019, 6:15am UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/15 "2019-02-15T06:15:35Z")
Looks great. Can’t wait to see how this turns out!! ---
**Author:** ![robandliv](https://forum.gbfans.com/user_avatar/forum.gbfans.com/robandliv/32/6600_2.png) [@robandliv](https://forum.gbfans.com/u/robandliv)\ **Post date:** [January 9, 2022, 9:19pm UTC](https://forum.gbfans.com/t/rgb-spirit-project/16689/16 "2022-01-09T21:19:45Z")
Can you share your file you used for the water jet cutter?