1st Scratch DOUBLE build FAST. Holy Moly this is a lot of work.

On to the Bumper today. So far it has been pretty simple. I have spent more time on other parts. I took the wood bit I glued up yesterday and printed out Stephan’s CAD drawing full size. I had to stretch it a bit to match my measurements. Then glued it to the wood.

image

Off to the Band saw and then belt sander.

image

image

Spindle sander to do the inside.

image

**I then glued 1/4" luane plywood to the top and bottom. Clamped it for a few hours. **

image

image

Then I put another copy of the pattern on and band sawed that shape and more belt sander.

image

image

Looking good.

image

**Repeat for the second bumper. **

image

image

This weekend’s goal was to get the pack on the Alice frame. That did not happen. So I busted out the skills and made it happen tonight. Some PEX plastic pipe for spacers and a wood “hockey” puck". I used what I had laying around.

image

image

image

image

image

**Wife tested it, she is 5’11" for reference. I will say it is not comfortable. The frame digs into my back. Going to have to play with the straps and try to get a better feel. Suggestions on making these more comfortable? It weighs in at 15lbs currently. **

image

image

Nice job for Halloween fun

Do you have the foam on the top of the Alice frame? It’s just pipe insulation from home depot. That should help of that’s where you’re feeling the pain.

The first photo of your wife, the pack is really low, those top straps need to be tighter to lift the pack up. Here is a pic of how it sits on my back. The foam on the Alice frame is wrapped in black gaffers tape, but I later changed it to black gorilla tape because the gaf tap was leaving black marks on my suit.

image

Thanks for this Jay. Yours if definitely much higher. The main rib going up the middle of the frame was rubbing my back. I will try it higher.

Finished the bumper from scratch today. Here are the center bits.

image

**

Glued and clamped on**

image

image

Originally I forgot about the center parts and sanded the edges round. So I had to fill that with Apoxy.

image

image

image

Some paint.

image

image

image

image

image

Overall I am very happy with it. You can hardly see the wood grain under the coats of glue and paint.

image

image

This is an impressive build! Very nice internal bracing for strength and also keeping material weight down.

I read through scratch builds for years! Took me a while to decide on styrene as my medium. Even then, following about 8 favorite builds, I still ended up doing things in different ways. These things when scratch built seem to want to be as unique as the builder. That’s a beautiful thing!

I am going to have to remember that diluted wood glue tactic for hiding grain for later projects! Thanks for the idea.

Shop is really called technology now? Do you teach how to build the tools? I jest. It’s still shop to me! :slight_smile:

Again, excellent build! The bumpers are gorgeous.

In hind sight it would not have been much more work to do styrene for the whole pack instead of press board. The press board, while light and easy to cut, has poor glue properties. The material pulls apart as it is just compresses paper. I will be trying my hand at styrene for the gun part.

Thanks for the compliments on the bumper. Yours is pretty amazing as well. Both our bumpers are awesome. Yours is slick and professional looking. Mine is super strong. Both have a unique way of construction.

Shop? Ha basically, but here in NY they have not called it that since 1980’s but adults still call it that. I am 36 and it was Tech when I took it. I teach grades 6-8 and we do woodworking stuff (catapults, Rube Goldberg, Bucksaws), rockets, CAD, Animation, Structures (bridges and trusses), keyboarding, Office, internet safety, 3D printing, and much more. I taught in Ohio and they had Industrial Technology. Woodworking, home Maintenance, CAD, Design and Drawing, Principals of Engineering.

Basically my favorite class everyday. Kids are interested when I bring a few parts of the pack in. I show them the CAD drawings from Stephan and what parts I have made.

Time for the N-Filter. Most people make this sooner, I had trouble finding a decent sized pipe. I ended up using a 2 1/4" electrical elbow. Any 2.5" pipe will have an outside diameter of just over 2 3/4". I happen to have this left over from running power to my detached garage. It was expensive, $8 for one part and I can’t return it.

image

Mocked up some paper.

image

image

Band saw time.

image

image

Used a template from the “How to Section” You guys rock on here for making some things just easy!

image

image

image

I am so grateful to see an upswing in classic scratch builds. This is looking great man! How heavy are they, there’s a lot of wood there.

I’m absolutely speechless.

My very first pack was mostly that same board. It’s usually made in Brazil and sold as Duratex. I was living there in the 80s so that stuff was available everywhere.

Btw, that stunt with the table saw.. holy crap talk about dangerous!

Been busy trying to get this done before my Oct. 22 party. I am also trying to keep things together on here, but in reality I am working on 4 things at once while I wait for glues to dry.

I think I left off with working the N-Filter. Cut it on the band saw, super glued the styrene sign on to it.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-09-29 21.17.53_zpsqqkiyzbj.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 14.20.34_zpsvu9vnjot.jpg)

I glued a piece of wood inside it and used a screw to attach it to the cake pan. I also put a piece of styrene inside to make the white for the holes. Then filled the gap with some Apoxy.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 17.33.24_zps0veizmlt.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 18.30.26_zpslyn4zijq.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 19.58.55_zps7i6secic.jpg)

After Apoxy cured, a little paint and she was good.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.18.05_zpsm4ob9e5h.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 17.58.39_zps1raosgjy.jpg)

Lets make some parts. I have some resin parts I picked up off Ebay, but I need two sets, so I made the second set and they are great. Crank knob is a top to something, dowel and a sanded down wire nut.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 17.43.48_zpswifaofbc.jpg)

Clippards are Bic White Out bottles. I dumped out the white out, let it sit open a few days and sanded off the bottom and part of the cap.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 15.19.17_zpshobxrgru.jpg)

Made some bases out of plywood.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 15.21.59_zpsxo55d68c.jpg)

Time to make some resistors. Just sanded a piece of wood and then plopped a wire loom over it. I also took the same wood and filed lines into it for the other resistor.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.43.44_zpsj8nci1ka.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-02 17.15.10_zpsbbwqs1ir.jpg)

Took a piece of wire, banged it with a hammer and drilled a hole in it. I know a pipe will cover the hole, but I like it. My home made ones and the resin castings.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.42.21_zps14fco2tx.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.42.26_zpsvrww72iq.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.42.49_zpsxglecdg5.jpg)

Also sprayed some 1/4" tubing. Not sure how well the paint will stay on this .

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-03 11.32.36 HDR_zpsagqplgkc.jpg)

Time to paint the end of the Ion arm.

image

image

Took the bolts I bought and threw them in some HCL (Muric Acid at Home Depot) then into some salt water for half a day. They came out looking like I left them outside for a while.

image

image

image

Time to wire!! **I found these reflectors at a flea market for cheap! Like $2 for 8 of them. So I scuffed them up and glued them in. **

image

I could not find nice plastic silver reflectors, so I covered cardboard egg cups in 2 coats of wood glue and sprayed them silver.

image

Then glued them down. The kit came from BK116 Chaser Kit, 16 LEDs. I also bought the FK116 Circular Chaser Kit, 10 LED from them. These kits were recommended on here somewhere.

image

I then had to run the wires through the foam. Making holes for wires.

image

image

Putting some Butt connectors on. I soldered some things and used these so I can take the wires apart and remove parts of the pack.

image

The battery will be in the booster tube, the on switch will be in the gun for all the lights.

image

image

So Pretty!!!

image

Then it was onto adding the detail bits. Pin in the crank knob to help hold it.

image

These came from Grainger with a reference number off Norm’s plans.

image

image

image

image

image

image

These are fittings I found at a flea market. They are some kind of compression fitting, but I paid $5 for a box of random brass stuff.

image

image

image

Nice work. Are you going to put some rods in the ion arm caps?

Yes and I have them but am afraid of bending them so they are last.

Attached some more things. I guess I have not said how I am attaching things. The brass bolts have a 3/8" diameter dowel under them that is drilled into the areas they are glued too. That just gave more meat to allow the brass nuts to stay glued. I used gorilla glue (polyurethane glue as it expands into the threads of the metal).

Here I went to attach the ribbon cable I picked up from Amazon. I tried a screw first, but the wood broke off, so I used 2 small nails.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 21.29.02_zpsf3b2uvdy.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 21.37.21_zpsnlf8tvxp.jpg)

Worked on wiring some more. I installed a LiPo battery pack from my old RC helicopter in the booster tube. I made a velcro sling to hold it and the top comes off the tube. Battery is 2100 ma, enough for lights for a many hours.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 22.15.29_zps8zpbgtk1.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 22.19.20_zpsf2j7zjdq.jpg)

I took a paper towel and sprayed some brown paint on it. Then rubbed that over the Alice straps to weather them. Nice and subtle.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 22.27.01_zpsftg3ttj9.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-06 22.34.25_zpsynrjcmxw.jpg)

To attach a Clippard I drilled a hole and put a nail in the pack. Then cut off the head and pushed the Clippard on it creating a dimple, drilled it and glued it with gorilla glue.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-07 17.50.51_zps5otxba4a.jpg)

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-09 18.45.26_zpsczw3r4va.jpg)

Added a 3/16" brass rod (1/4" was like $15 for one, this was $3). I polished it and then put it in my drill like a drill bit. I ran a file over that rough spot to add a little detail. Installed by drilling a hole a smig smaller then the rod and hitting it in with a hammer.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-09 18.45.47_zpshvj9lqvi.jpg)

Weathered the pack with some silver spray paint on a paper towel and touched a few areas, just needs stickers, shock mount, and a gun now.

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-09 18.45.40_zps9dq2kclw.jpg)

Started to really hammer hard on the gun. I have to have this all done by Sunday as my party is a week from Sunday.

I have one home made REVERSE gun and a resin gun. Due to time, I am not making a proper gun and will run with the reverse one. I used a lot of epoxy to attach the pipes. Buy the big jugs of glue, they are $16 for like 16 oz in the epoxy section of HD.

image

Fake welds, not great, but they work.

image

I super glued this 3/8" diameter dowel and then added Apoxy fake welds.

image

I cut some styrene to make one of the end pipes. This is just 1" pipe. I heated it and used Weld #16 glue to attach it. I am sure super glue would also work. Then clamped it with a string.

image

image

image

I put a small screw in the gun and then used a lot of epoxy to glue the pipe over the screw. This way the pipe is glued to the gun and screw, lots to hook to.

Here you can also see my knobs made from screw on milk caps and water caps. Glue together and on with gorilla glue.

image

Just been chewing away a few hours a day. Party is in 10 days! This thrower is tough stuff.

Made the rail with 1/4" plywood. Cut out some parts on the scroll saw.

image

Then glue them together.

image

image

Finished up this cut off knob thing. Cut it with a coping saw then glued styrene to the open areas. Little sanding cleaned it right up.

image

image

Then on the the block bits of the thrower. Cut a 1" square piece of pine on the table saw. Chopped it up on the Miter saw and drilled some holes for electrics. Then glued them to the box with gorilla glue on the wood one and epoxy on the resin one.

image

image

image

I printed my stickers! I downloaded them off this site from Valentino here: Pack and Slime Blower Decals - Proton Packs - GBFans.com

Just go to the last page and there is a link. First I picked up sticker paper from staples and then metallic off amazon. The metallic did not work in the laser printer, the ink did not stick right. It turned out ok on my ink jet, just need to put some clear coat on it or something so water will not make it run.

The middle one is the laser and the colors are all off. Total cost was around $5 for the 4 sheets, much cheaper then buying them here or on ebay. I should sell them on ebay for $20 each!

Anyone have a diagram of where these all go?

![image](http://www.gbfans.com/images/pb/xyster101/Ghostbusters_2016-10-14 22.42.41_zpskts41lkf.jpg)

Wish I had the tools and the talent to go this route. Your build looks really great!