First I just want to say Hi to everyone because this is my first post. I’ve been using this site as a resource for my proton pack build and not once did I need to ask a question, found everything through the search. Horray for newbies who can use the search function!
It was the end of June and with another whole month to go before school starts back up, I was dying for something productive to do. I’m a laser engineering student and originally my plan was to construct a portable CO2 laser with a backpack mounted power system so I could take it outside and set beehives on fire and the like. I was searching “ghostbusters backpack mount” on Google because I figured I’d use the same system for my own project. When I found this site, I not only found what I was looking for but I was also inspired to build a replica proton pack as well simply because of how cool it looked. So I borrowed my dad’s jigsaw, hauled an old sheet of 3/4 inch plywood out of the shed and set to work.
It was about this point where I completely lost interest in my original idea and started working on the proton pack exclusively. At wal-mart I found the requisite turntable, but I couldn’t find the cake pan needed. I instead went with a similar pie pan but the edges have a more gradual slope and as such the cyclotron is a bit smaller.
I went out to home depot for some MDF, but the only mdf they had in a size that could fit into my little Cavalier were pre-primered MDF shelves, 3/4 inch thick! So I spent about an hour a day working on the pack and little by little it came together.
I didn’t realize until it was too late that I glued the ion arm down backwards. Oh well, not many people will notice! The synchronous generator is made of a large corrugated plastic sign, the rest is made of the 3/4 inch MDF on a plywood motherboard with various PVC pipes.
Officially this is a test fit…
… but let’s not ■■■■ ourselves. I just wanted an excuse to wear it.
I put a first coat on the cyclotron, and used some old trailer brake light lenses for the lights. It was around this time I realized that a totally movie-accurate build was going to be impossible, considering this had been the first time I actually built anything more than a simple box from scratch. The bumper isn’t anything special, but to spice it up a little bit I decided to leave the metal L brackets exposed. I also ended up making the gun mount box out of three failed ion arm cuts out of MDF, with the nicest one on top and the others underneath. The EDA is screwed into the motherboard from the back to house the electronics. By this time I was so tired of cutting wood that I skipped the cosmetic plating on both sides of the synchronous gen and just cut out an L-shaped piece of styrofoam and glued it into the middle. The injectors are capped with duct-tape and electrical tape. The fins on the gearbox and power cell are strips cut from wooden paint stirrers that you get for free when you buy paint from home depot. I had to modify the fin design on the gearbox to hide the gaps in the box which resulted from shoddy cuts. I used some old putty to fill in the many cracks and gaps all over. The brass rod on the ion arm is actually a copper rod. Since brass rods go for $15 at home depot I just cut up an old copper lawn ornament and used it instead.
I built the electronics package from scratch.
What I have here is a PIC18F4552 microcontroller which is directly driving blue LEDs, all of which have a common ground through 160 ohm resistance. They only light up one at a time, starting from the bottom and moving up to the top, then repeating. The micro is running on its internal 4MHz clock. The cyclotron lights are red LEDs that are also directly driven in a similar fashion. The whole package is powered through a 5V regulator connected to a 12V 4.5Ah lead acid battery. I also ran 12v power to the proton gun which contains the master switch and also some constant-on lights. Overall the entire electrical draw is no more than 45mA which gives me about 100 straight hours (4 straight days) of running time.
After a quick coat of primer
The pack was finally starting to look good. I then painted the whole thing, by hand, with a half inch wide paint brush. I used acrylic paint from the dollar store and frankly, it doesn’t even look that bad, despite taking a long time to paint.
Ad this point I decided I was finished fiddling around inside and glued down the cyclotron and started on the finishing details.
Just as I was finishing up the pack my order from MMM came in with my resin gun parts, and so I set to work getting that together.
I actually went from that stage pictured above to essentially finished in one sitting, so I don’t have any further intermediate pictures. And so without further ado, the finished pack.
As far as the proton gun is concerned I didn’t spend nearly as much time on it as the rest of the pack. I used a different style heatsink, the business end uses a copper pipe instead of a clear one (I kinda like how it looks). It doesn’t even have a trigger box, only a single switch. I used only red cliplites and only one coat of paint.
There actually isn’t any one part of the pack that is actually movie accurate, for instance the label placement isn’t right, the HGA wires are swapped, the booster frame isn’t correct, ion arm is backwards, ribbon cable doesn’t go to quite the right place, etc. But I still think it looks pretty good.
Also, being made almost entirely of 3/4inch MDF, the pack is heavy! I weighed it, just under 30 pounds, making it by far the largest, heaviest thing I have ever made.
I guess the pack isn’t really finished. I plan to upgrade it, bit by bit, over the coming months (years?) with things like a proper bumper, better paint job, more accurate parts, etc. But for all intents and purposes the hard work is done. I’ve already got a tan flightsuit and my mom is in the process of sewing the no ghost patch on it as I type this. Next up, ecto goggles, then maybe a ghost trap, and I also might get no ghost decals for my car…