Is there any chance we will see “Ghostbusters II, The court room figures?” Ray with the skinny scoleri brother, Venkman with the fat, and Egon with a trap?
will we see maybe a ghost pack or maybe a pack of attachable proton streams to clip on the end of the gun just like we had on the trap that came with the 6 inch winston zeddemore?
Though I haven’t tried it yet. You apparently use a hair dryer to carefully heat up the head, causing it to become soft. The head is connected by a ball joint ( you don’t want it to heat up so only keep the hairdryer on untill the head is warm and soft). When the head is soft and the ball joint still cold (and hard) the head can be carefully and gently pulled off. Then you can swap them.
Hey guys I just wanted to point this out, according to Matty Collector’s website the Walter Peck figure does not come with an extra (closed) trap.
-6” Walter Peck™ Figure — comes with containment unit and can place trap inside (trap comes with Winston)
This came from their news page. If this is true what a sinking ship this toy line became, in my opinion.
Also my question for the next Q&A session:
“Since the consumer is paying a premium price for an ‘Adult Collector’s’ item can the quality control be more scrutinizing so that there are less damaged/deformed figures (i.e. bent limbs and crooked wands)? If this not obtainable, is there a possibility of packaging the figure in less compromising pose?”
You’ve GOT to be kidding me… So because the figure doesn’t come with a tiny trap, that’s probably worth about $0.40, the toy line is now a sinking ship?
Even if he doesn’t then at least it’d use the Winston trap. They could have made it take no trap at all (and that would have truly stank) but at least it adds a but of interactivity between figures (like how Winston’s trap beam holds Egon’s Slimer).
I have not done this to these specific figures either , but i have done it with figures with similar joints, its pretty easy to do.
I’m not sure it the head can be “gently pulled off” but i would definitely never try this without the hair dryer!
on a side note.
I hope they Make a Rookie figure with at least the slime blower upgrade, or interchangeable packs with the other various upgrades.
i think its odd that the sniffer has been made before the pke meter and ecto goggles.
it would have been nice to have a pke meter, goggles, And the sniffer with the lab coat Ray, unless a lab coat Egon with pke meter, or lab coat Peter with goggles will be made, I’m not too big on the sniffer with Ray so i don’t see much reason for me to get lab coat Ray.
I recommend the “Boil and Pop” method. It’s safer than the hair dryer method. You’ll need a pot of boiling water deep enough to submerge your toy in head first to the shoulders without the head coming in to contact with the bottom of the pot. You’ll also want oven mits or better yet silicone gloves.
It’s the same idea as the hair dryer, but there’s less chance of burning or melting. You get your water boiling and then dunk the figure’s head and shoulders in the water. How long you leave it will depend on the plastic. When he’s soft enough bring him up, grab the head with one mitted hand and give it a good pull and it should pop right out.
The only potential issue to be aware of with boil n pop., is in some cases, the connection ball inside a part is made of thin or somewhat fragile plastic if heated.
Since you are immersing in boiling water, the water will find its way to that connect peg.. if it gets too hot, and is the fragile type (or is the soft plastic type) then the peg itself can actually rip off, or if it has a bal at the top, pulling on a part connected can actually tear the ball right off the inner peg.
I use a blow dryer or heat gun if I’'m unsure of how something was assembled, because the inner pegs are not heated, and you have a smaller chance of destroying them.
Im with skywarp82, I couldnt of said it better myself with the GB2 figures, these would totally sell. But realisticly if they made these they better make all four GBs in the dark suits with Winston and Ray with the slime blowers. Also am I the only one that wants to see like a 3ft stay puft or 3ft staute of liberty that comes with Ray and the controller you could open the back of her head and put all four in. Dont give me the stink eye if we talkin toys lets go all out gimme the ecto 1 as well and if they make a line for the video game the boat.
First of all, if the guys are about 6 in, thats a scale of roughly about 1 in = 1 ft, so a Stay Puft or Statue of Liberty figure, if made to scale, would need to be about 100 in tall, or roughly 8 ft (just pointing out how big this figure would need to actually be if its to be in scale with the line).
That said, I know you didn’t say it had to be in scale, but the figures would look awfully weird if you could put them inside Lady Liberty, and she wasn’t to scale.
I definitely want to see an Ecto-1 though, I agree with you on that, but I think we’ll need to see variant figures made of each of the guys where the packs are removable so that they can properly sit in the Ecto.
The price will probably be $30 though… so you guys won’t buy it and just complain. Plus it doesn’t come with an accessory bag of Marshmallows, so its a total rip off.