HD Reference pics (Update 11/20 - New GB1 caps on Pg 6!)

Moderator’s Note (September 15th, 2015): Here are some alternate links to the original galleries:

Ghostbusters HD Reference

Ghostbusters 2 HD Reference


Right click for full view!

image

image

image

image

image

image

image

image

image

image

image

image

image

Things I noticed when looking at these:

  • Those belts sure do look awfully white.

  • The aluminum gun knobs were painted black in the first film.

  • There are some stacked brass washers held on with bolts on one of the tubes on the gront of the gun box. Looks like three on one, and two on the other.

  • There’s an odd shaped white thing on the front of the trap pedal which the ribbon cable attaches to.

  • The bellows on the trap pedal looks like it could be some kind of fabric stretched over some kind of spring rather than made out of rubber.

  • The silver knob on the front of the trap has a black insert in it, and the black knob has a silver ring around the top.

  • The square knobs on the front of the trap don’t have the silver insert in the top.

  • The design of the ribbon cable in the reference section looks like it’s spot on. (I wasn’t sure about that since I hadn’t seen the high res caps and you can’t really tell from the low res ones.)

  • Ray has cake on his boots. ( Just making sure you’re paying attention. :slight_smile: )

These look great. Where did you get the HD source from?

Santa. :slight_smile:

*Someone finally believes me about the belts, however over time I’ve come to believe that they’re either a white pistol belt that’s just dingy-dirty, or a VERY faint grey…

*And the knobs I’ve noticed for awhile now…I’m just surprised nobody else picked up on this :sigh: …

*Two other things of interest:

-The rubber “safety gloves” have a “grip pattern” on the palms.

-The heatsink on the gunbox doesn’t seem to have grooves.

*Cheers.

I’ve always believed they were white. :slight_smile:

Also:

But they were khaki in GB2.

As for being dingy… or grey… Well, if you look at the color of the ghost and compare it to the belt, it’s clear the belt’s not super white. Arguing over whether it’s light gray or dirty white however is silly because that’s just semantics.

However, as far as practicality goes, I’d perfer to call it a white belt, because it’s a lot easier to make a white belt darker than it would be to lighten a gray belt to that shade, which looks to be about 75% white. (I’d estimate the lightest of the armbands in the shot where they’re approaching gozer to be about 50%)

i think only one gun had the knobs painted black. it was some kind of hero close up thrower (note the lack of any labels also).

Yep, throughout the rest of the movie you can clearly see instances where they were not painted black… That one thrower they used in that zoom in shot shouldn’t be used as the definitive representation of what was used in the movie, just an example of one thrower…

Yeah, I just checked and in every scene I’ve found other than that one so far they remain unpainted.

Looks better that way anyway. :slight_smile:

More caps! Merry Christmas. :slight_smile:

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

image

New stuff I’ve noticed:

  • The holes in the n-filter don’t look very white, in any scene I’ve been able to get a look at them, unlike the GB2 packs. There’s also a gleam which appears in that area on two of the packs as they walk down the hall near the start of the film. I’d been considering putting a bit of screen in there because they look like vent holes. Seems like that would match with what I’m seeing, though obviously there’s no way to ever know what was really in there.

  • The washers on the bumper appear to be brass.

  • There’s a couple stickers around the side knob on the ecto goggles.

  • The trap hose is not loom in general, but there is some loom in the bundle of cables when Ray is holding the traps. One of the traps may be conencted to that, it’s hard to tell. Also there’s black “tape” on the location where the red “tape” appears in the slimer scene.

  • Blue top warning label on one of the packs coming out of the car.

  • Top of the motherboard appears to be attached to the alice frame with one screw through the center bar, and nothing else.

  • There appear to be a number of red wires on the belt circuit coming off the right side of it, but I can’t make out enough detail to figure out what’s going on there.

Most of this stuff has been discussed before, but it may well be lost or buried now so I’ll try to recap some off the top of my head.

As are the ones on the “locking” screws on the front handle of the gun.

They’re rub-down transfers the same as the two on the gun under the toggle switches (beside the bar graph).

I think this was discussed here that the “hero” trap pedal had a soft black rubber air hose (no longer made), while split loom seems to have been used for stunts or filler. I think someone here said they had an old air hose that matched.

There’s never been proof (even with the HDTV transfer) that there’s a blue label on the top of the pack since it can’t be seen anywhere else. People have argued multiple times about it and what might be the cause of what can be seen. Personally it looks as if the colour layer of the sticker has been peeled off of it’s foil backing (the one PH hero pack shows this same separation at the corners).

See photos of the correct Sanyo ICC-808D calculator circuit board to clear up the source for the red wires.

Hope some of that helps.

As John has stated it’s probably just the color layer removed from the metallic backing…

This reference shot shows the whole red color layer removed on that same sticker and could very well be the same pack seen on screen in that shot…

http://www.gbfans.com/images/equipment/reference/29/71.jpg

Look at that deep khaki color on the uniform, no hint of gray on the wet spots ; )

Missing something on the rear instrument bar of that gun(s), huh?

Lots to discover GhostGuy I have stepped through the movie frame by frame in HD dozens of times already…

There’s better shots than that if you want to argue they’re khaki. :slight_smile:

image

I think it’s more interesting in the above shot that the slime on the floor appears green, while the slime on Venkman does not.

Found via google… dunno why it’s not linked to in the props section:

image

This is the one I’d been using for reference, which explains why I didn’t know where all those red wires were coming from:

image

*Fan-made?

*Cheers.

Oh, yeah, you’re right:

http://www.gbfans.com/community/viewtopic.php?f=4&t=4156&p=34356

Person who posted it said it was a real one, but then Exoray says it’s someone’s scratch built reproduction.

Yeah thats Playskools…

Lawrence

Different revision of the calculator…

image

Same calculator, one on the left is an earlier build, the one on the right is a newer build, notice that the nixies have been replaced with an LED panel, some of the discrete components on the lower left have also been replaced by ICs… But also notice the newer one has red tubes over the legs of the one component…

The “real” screen used one even had many more discrete components on the lower left… I have heard the exact correct one was found, but I have never seen a picture to verify it…

As I have said multiple times, the electronics (computer) age was making advances literally every day back then, with the original price of these things close to $1000 (yes $1000 in 1971) companies like Sanyo were constantly revising the insides trying to lower the price… They kept the same model numbers and kept the same plastic housings but changed up the PC boards configuration often…

This is why I warn people constantly not to go crazy and overbid these damn things when they pop up at auction, it’s truly Russian Roulette on what you will get when you pop it open…

And last but not least yes the one found by Google is Playskools replica, he built it using from what I gather a poster of the guys as reference…

I’ve thought for some time that it looked like small screens on the N-filter in some scenes, I’m glad I’m not the only one…Even if it’s not, I think it would be a bit more visually interesting on a pack. Aerator screens from any household faucet should do the trick, I’m thinking about trying it with my pack.

the white dots on the N-filter is indeed a white mesh type material glued inside the shell. and as there are holes cut out of the filter you can see the mesh :slight_smile:

also…

how the hell is Venkmans thrower clipped to the pack in that scene if the gun track is facing away from the pack???