My Pack + Uniform: WIP

Thought I’d start a work in progress thread for my own pack and uniform since I’m just starting on the woodwork now.

My plans for this pack and uniform were from the start to make it as screen accurate as I could within my budget and time constraints. The budget was blown on the uniform, what with all the dyes and patches and hoses and connectors and belt and belt circuit and a set of Bates side sip paratrooper boots. At this point I’ve spent 3x as much as I budgeted. But as a result I have many real and resin replica parts, like resistors and elbows, and I have shifted gears from doing a simple foam pack with pringles cans and laundry detergent caps to doing one made from MDF, PVC, and resin.

Since reaching that point, I’ve decided a light system was also a must, as is sound. The pack might be cool in and of itself, but a light show and a sound system will really push it over the top at parties. To that end I have purchased the neccessary components from Mouser to build my light circuit for the power cel and cyclotron, and have bought a set of small computer speakers which I have jury rigged with six C cell batteries, to connect to a small USB mp3 player which I will attach to the gun for easy access.

9/6:

Finally gave in to the idea of being a Ghostbuster for halloween and began shopping. Went to military surplus store. Looked at flightsuits, found belt and alice frame that I later learned needed repairs due to a missing strap for the kidney belt and a broken buckle. Found soldier’s painkillers in a plastic bag in the bottom of a well used army boot. Suggested to guy at surplus store they were suicide pills. ATM ate one credit card. Went to another surplus store looking for side zip boots and a better flight suit. No luck there. Went to Walmart, Home Depot, Ac Moore, Michael’s Crafts, Lowe’s, and Sports Authority. Bought all this ■■■■:

image

9/7 - 9/17:

After ten more trips to Home Depot, the above stores, the local mall, and an electronics surplus store, measuring every tube and washer, examining all the wires and tubes, and picking up a few small tools, I visited my sister and picked up a bunch of my dad’s old tools, since I had none. Then I decided I needed a toolbox to store this ■■■■, so off to Sears, where I also picked up a hole butter bit for drilling the cyclotron light holes in my cake pan.

In addition, I visited another army surplus store, and found myself both a large and an extra large Rothco suit, which was like the ones at the other surplus store that I’d turned my nose up at, but I didn’t want to order one online and get the wrong size and I didn’t have any options left. I got the XL even though it felt like I was swimming in it because I thought the baggy look would be better and I thought it might shrink. This turned out to be a very good decision*.

In the meantime, I also dyed my suit multiple times to get it the right color, and dyed three lengths of hose after making one bright opaque yellow by accident and the other amber based on a publicity photo I was using as a reference which had a color tint. Third time was the charm on both I guess.

(* Because six times through the washer and dryer with a several baths in boiling water between to remove color and dye it resulted in a perfect baggy fit.)

The result was all this ■■■■. At this point I thought my apartment had looked like a bomb hit it:

(If only I’d known how it would look two weeks later.)

image

image

9/18 - 9/26:

More shopping for parts, both in stores and online now. I have placed orders for resin parts, and all the parts I need for my light kit. I’ve bought real resistors, resin replicas, and hoses from Multimedia Mayhem, aluminum gun knobs from Ebay, and vinyl stickers Dr. Sparky. I’ve got a dixie v-hook from ExoRay. I’ve bought spraypaints and aluminum paint, and glues, basswood, and a tape holder and a leather keychain to go on my belt. I’ve also got the mp3 player, and the speakers. My Mouser order has arrived, as have most of the things I ordered online from those mentioned above. I’ve rigged my batteries to the speakers and they work like a charm, loud enough, with plenty of bass. I have sprayed my alice frame, I have constucted my ion knob from washers, and I’ve colored my belt circuit pouch with permanent magic marker which stinks to high heaven but should air out after a week in the hall like the leather keychain did. I’ve also built most of my fake cardboard and styrofoam belt circuit:

image

9/27 - 9/28:

Began construction of the gun. Sawing this basswod is a total bitch. It took me an hour and a half just to cut out the sides of the gun box. If you plan to do this, here’s a word of advice. Don’t get the “fine” craft saw. I had to buy some coarser craft saws just so I wouldn’t be at this for two weeks, but even those are ■■■■, but at least I can cut through one board in five minutes. If you’re working with foam, I ENVY YOU.

Placed more orders with mutimedia mayhem. Make that switchbox out of basswood now that I know how hard it is to work? You kidding me? Time is short and I have five more boxes I have to construct with ribs all over the damn things for the main pack. Plus I have to cut five sheets of MDF and make a router jig. Christ. Why didn’t anyone tell me how much work this would be? All I wanted was a kickass halloween costume!

image

I can’t say I’m not having fun though. Working with wood and electronics were two favorite things as a kid. That and chemistry… which I may be doing a bit of to make the same sort of slime they have in the movie. That overpriced green ■■■■ I bought at Walmart is going back.

Btw, the plan to have this done by the 15th for an early party I’ll be attending. Want to take bets on whether I can get it finished by then?

More photos as they become available!

Built my gun box today:

image

image

image

image

Yay!

image

Shit. :frowning:

How the hell am I gonna fix that. Bondo? Another piece of wood I’ll sand down? Cut the front and angle off with a razor and replace both and bondo the sides to make it fit? I don’t know.

Why worry about it? It’s not like it won’t "work"without changing it.. :wink:

And ya KNOW in the last 25 years, Ghostbusters Inc would have upgraded equipment by now.. god knows they didn’t even have led lights back then!

If I was capable of taking that attitude I’d still be making this thing out of foam and I wouldn’t have blown 3x my budget on parts. :slight_smile:

If you want to do it right, you’ll have to bite the bullet and remake it. I don’t know how many times I’ve had to remake parts on my pack but if you don’t do it now, you’ll only regret it later.

On a side note, this looks to be a very clean build and I am looking forward to seeing what you produce here. It could be something great, but I’ve seen good packs go the way of bought parts in the past to get excited now. We’ll see I guess.

Cole,

Looks good enough to me!!

There was enough variation in the original props to get away with it I’d say.

If it looks good and right then there’s no need to worry, If the angle was really off then yeah, something would have to be done, but for that amount… I reckon you will have bigger inaccuracies than that, which you wont even worry about or notice!!

Nice build on he box!

Lawrence

nice work… thats going to be very satisfying once you’ve completed it.

Ghost Guy…don’t worry about slight variations like that. They’re perfectly acceptable.

As long as you’re within 1/8" of all your measurements, you’re fine. :grin:

…but that looks like he’s off 3/16" off to me… :wink:

Just kidding man, it’s your pack so do what 'ya want. That’s half the fun of building your own. I’ve altered measurements on mine numerous times to make it all fit. Only in CAD do Stefan’s plans work perfectly! :slight_smile:

Well, we are using foam, and various other goodies as well. Thign is, we live in the sticks, so my choices are order everything online, and pay a buttload of shipping as well for things, or find usable substitutes locally. Since my wife will also be wearing a pack, weight is also an issue.

Looks like our packs n guns will weigh in at about 10 lbs tops.

Here’s my new WIP thread.. might give you some ideas..So far for two outfits and packs, we are at about $220 or so.

Repair successful!

image

I didn’t want to just sand the whole piece at an angle because that would have made the top too thin.

And I couldn’t overlay the new piece over the old one because that would have made it too thick to mount the switches.

So I used a razor to carefully remove the original angle part, and then I made a new part which was as wide as the whole box. Then, using a razor, I shaved angled channels 3/16" wide down the sides only. That way, when I mounted the piece I could glue the sides of the top half of it to the side of the box, and glue the bottom of the sides to the top of the sides of the box near the base. This allowed me to build the thickness of the bottom of the angled portion up, while leaving the top portion’s thickness unchanged. And the integrity of the box hasn’t been compromised. Once I sand it down and fill the crevices with glue or bondo, you’ll never know the difference.

I also forgot to mention in my last post that I reinfoced all the corners with a bead of glue on the inside of the box. Judging by how difficult it was to cut the front piece off with a razor, this thing isn’t in any danger of ever breaking.

D’Oh! Forgot the link!

Well sorry to dissapoint, but due to time constraints, budget constraints, concerns about dirability, and just plain difficulty of construction, I’ve had to buy some parts. Most of the rest of the gun will be resin, acrylic, and PVC parts purchased from multimedia mayhem. But most of the pack will be made from wood and a cake pan. :slight_smile:

I didn’t buy anything that was inaccurate in shape or had fake looking welds all over it if that’s your concern. I’d have loved to have made the whole pack from scratch, but even if I had until halloween to build it, it wouldn’t be enough time to do everything. Don’t forget, I not only have to build this whole thing in two weeks, but I also have to construct a light circuit, and mount my speakers and mp3 player inside, and finish my belt circuit.

Time is tight!

Well judging from your skills I’ve seen on this gun, I hope you take a crack at making those pieces yourself after Halloween. That gun just looks so clean and organize, I’d love to see how the rest of the pack would end up! But I totally understand the time constraint as I’ve done the same exact thing. Hopefully you get her done in time!

GhostGuy, check out my wip images.. I’m only at on actual day of build after shopping, and I already have the basic pack shape.. and those electronic boxes at lowe’s are a godsend! Cheap, durable, and about the right size, with some great techy looking detailing.

It’ll take you about 40 minutes though to remove the nails, and use a dremel to cut off all the nail connectors. (Rather then elaborate sanding, i just used a dremel grinder to smooth the areas close as possible.)

Use the dremel on it’s highest speed, and use a FIRM hand when cutting, so ya don’t cut yer damned leg of though! LOL!

(Plus hot melt glue should stick well to them, or better, screw them from the back of the motherboard, for a more durable (and easily removable) cheap temp solution.)

Honestly though, odds are we’ll stick with what we are building for quite some time, since they appear to be pretty good looking so far.

I’ve been watching everyone’s pack builds, including yours. :slight_smile:

The electric boxes are a great shortcut if you’re not going for a screen accurate look, and originally it was my plan to go that route, but then things got a bit out of control.

First I found the right belt at a surplus store, which I thought was impossible to get at the time. Then I found the right kind of ribbon cable for a GBII pack at the local surplus shop, which I thought was even harder to get. Then I bought paratrooper side zip boots, and there went my budget.

From that point I bought real resistors, resin replicas of the gun handles and gun ears, a resin Raytheon crank knob, vinyl tubes and wire loom hoses, and an acrylic gun tip. And most recently I’ve purchased aluminum gun knobs, vinyl stickers, and more resin replicas of knobs and elbows and things that I couldn’t find inexpensive real alternatives to. I also found a pair of the Markwort knee pads the other day online. :smiley: (Sorry; they were the supplier’s last pair of any size or color, and he won’t be getting any more.)

Then there was what I had to spend on new tools, like hole saws and the like. And all the craft supplies like paints and dyes and a compass, or $35 worth of resistors, capacitors, IC’s, breadboard, wire, LED’s, and sockets for my light circuit.

All in all, not counting stuff that will be returned like the crappy dremel I bought for $50 that does nothing well, I’ve spent about $650 on the uniform and pack. And that would only go up if I were to now purchase a bunch of electrical boxes and things to take a short cut. And, it would be crazy to stick all those real parts I spent absurd amounts of money on on electrical boxes and foam. :slight_smile:

PS:

And you want to know the funniest part? When I started this, I wasn’t even that huge a ghostbusters fan*.

What I’m a huge fan of is celebrating halloween, which I hadn’t been able to do properly in years living in the city. But, when a couple years ago when I won $300 in a costume contest dressed as a zombie in a bathrobe, I found a way to celebrate again, and each year I plan to try to outdo my previous year’s efforts. And win more cash. :slight_smile:

And as luck would have it, just when I was looking for this year’s project, a true GB fan put the idea in my head to do this… and despite knowing it was going to take a hurculean effort and mucho bucks to do it, even if I went the cheapest route… I couldn’t resist the temptation.

And now, I wonder, when I complete this, what in the world I could possibly do to top it next year. :slight_smile:

  • Of course I enjoyed the films a lot, like most people, and wanted to be a ghostbuster when I was a kid, but until I started building this thing I hadn’t seen more than bits and pieces of the films in years. But after all this work and rewatching the films for research, I’m starting to come around. :slight_smile:

Well you are off to a great start man.

Keep up the good work.

Well, it’s all about your passion level, and eye for detail.

While I’ve always loved the ghostbusters movies, so long as my stuff looks right to the general public, I’ll be happy. We’ve gotten many or the proper parts, flight suits, pistol belts, proper goggles, ect, but I’m not going to loose any sleep if I can;t locate transistors or such, and I’m not paying $35 to someone for a resin part that should cost under $10.

Long as kids and adults see us, and think it looks “right” that’s all that’s important to me. If we decide to accurize them down the road, I’ll take my time at it, but so far everyone who’s seen what we are doing and aren’t ghostheads, think it’s amazing, and thats good enuff for me.

It’s amazing how it all builds on itself. I was thinking if I could make my own knobs and etc. out of bottle caps, I’d be happy. But, my brother (whom I dragged into this) is getting crazier than I am and is sourcing all the actual parts…it seems horrid to put some cheap bottle cap knob next to an actual Legris elbow and dale resistor… :blush:

Yep. :slight_smile: