My Proton Pack build (Benofkent kit builders please give advice !)

Are you planning on mounting your electronics on your motherboard or directly onto your shell? If you choose the former, the placement of your hole for your loom could be problematic whenever you remove the shell from your motherboard. I had to cut a “mouse hole” on the edge of the shell to avoid needing to feed the loom through the hole, like so:

Obviously, you might have other plans in mind for your electronics. If that’s the case, please ignore my post. It’s just something to think about down the line.

I have been trying to find the clamp you are using Canpara but have had no luck.

Nice idea but a bit late now I’ve cut my hole I guess lol, plan was to use a zip tie to keep the loom in the hole, not even thought too much about electronics yet as they are expensive on GBfans for UK buyers :confused: one bridge at a time, still worrying on drilling holes on pack and building the wand lol

While I wait for Taps to arrive so I can drill holes in my shell for the build, I thought I’d get the motherboard onto my Alice frame.

Benofkent did me a favour and marked where on the board to drill holes and provided some 3d printed spacers.

I then Painted and placed the Warning sticker on

I purchased mine from Bionic Moon Labs (bishopdonmiguel on GBFans) and I cannot recommend it enough:

I see that the GBFans thread is locked and the Etsy store is sold out. However, you could try messaging bishopdonmiguel directly. He’s a swell guy and very helpful.

If you do contact him let us know the reply as I was going to be doing the same in the new year as I’m hoping to start a very similar build (hoping by Easter time)

So I got my drill taps to start the holes on the shell. Started by trying to get the hole I cut too big due to an incorrect sized pipe corrected using Car Filler sent by Benofkent. First time doing this it was messy and tricky lol bolted it in place and sanded down a little. Might sand it a bit more / top up filler in places. Will look neater once painted. Next Job is the Bumper

so I did a fair bit on the pack since I got my taps to drill with, bolted a few parts in place and prepared the ion arm

Best i can do until a few bits get delivered, then the wand to do, not looking forward to that

Yeah I haven’t even attempted to start the wand yet.

Looking great! Don’t let the thrower intimidate you, if you’ve come this far you can go further. I was nervous about the thrower too but once I started I had a blast building it. It’s hands down what I’m most proud of on my pack.

Get a roll of painter’s tape (blue 3m tape) and dry assemble the BOK wand. That’s what I did and it made me feel much more comfortable moving forward because I could visualize the construction and mods I would need to make without having to just do them blind.

Put on some stickers and got the V-Hook in place. Just waiting on some clippard hose holders to arrive to finnish off the main pack part now. (other than putting in lenses and getting the Crank in place)

Looks good. As for myself I did my first test fire of my pack last Saturday. Still have yet to begin the wand though.

Man that looks awesome! I have spoken to Ben multiple times the last few weeks and he is in no position to build me a pack! I am hopeful I will have one built by him and headed my way in time for my Halloween party and Disneyland Halloween this October! I am keeping my fingers crossed! I am in no position to build one of these myself, as I don’t have the time nor the craftsmanship LOL. Keep up the great work on the pack!

Sadly Ben no longer sells fully built packs, only the kits. Honest I have NO skills, never used a drill or dremel in my life, If I can do it you can! give it a shot

Rest of tubes now on, hardest part of the build so far getting the blue tube to bend on the top bit of the Ion arm …

Next stage is the wand once i figure out where to start ha, ordering electronics end of the month

I was worried about bending the green tube on the wand when I built my Anovos kit, because I didn’t want it to kink, so I heated it up with a hairdryer to soften up the plastic a bit… Helped a lot! When I got to attaching tubes to the pack itself, I ordered colored tubes from the GBFans shop… It was a much softer, rubbery material, and they all bent nicely without any need to heat them.

nice idea about heating up the tube, will try this when I do the wand. May in future upgrade to the GB fans blue tube

Your build continues to get better and better with every update and gives me confidence that when I start my own (soon, only been planning it for 10 years!) I will be able to do it justice!

Looking forward to your future updates :slight_smile: