My wires have been breaking everytime I turn around.
The actual wires or the solder?
You can wire wrap instead of soldering…
The actual wires have been breaking… Now I am having trouble getting the wing lights to fit in the wings and not hit the other electronics when they extend. And the ribbon wire that is on mine is different from the one in the picture, mine is more like the one on the front of the trap pedal. And very stiff.
Are there any schematics for just running wires and LEDs? That would proly be easier than the PCB Boards in the wings.
Are there any schematics for just running wires and LEDs? That would proly be easier than the PCB Boards in the wings.
I would think all those wires would somehow hinder the wing movement a bit. Anyone have any experience with that?
You need to use stranded instead of solid core wires. Though if you’re using a kit and not building it yourself in the first place you’re probably SOL on that count. :whatever:
The actual wires have been breaking… Now I am having trouble getting the wing lights to fit in the wings and not hit the other electronics when they extend. And the ribbon wire that is on mine is different from the one in the picture, mine is more like the one on the front of the trap pedal. And very stiff.
Just seperate the ribbon. I had to heat up mine for a few seconds with a heat gun to soften the glue he used to hold the wires in place, then gently push them into a right angle. The glue will harden and they will stay flat. To seperate the ribbon, just GENTLY run an exacto along the joint or pull them apart. I do not suggest pulling since the wires are very soft and can snap. My PKE build hasn’t been too bad, but you just have to take your time. So far, I just have to mount the last servo and adjust my second wing to fit the board.
Thanks for the info.
You guys need to brush up on wire layout. ![]()
I’m guessing the wires are breaking at the solder points to the arm.. Yes?
Copper has a cubic crystal structure and bending a copper wire “work hardens” it, which introduces defects known as dislocations into the structure (jagged crystal shapes). Basically, the more you bend anything copper, the more brittle it becomes. And that is happening to the end of the wires every time the arms move up and down.
Yeah thick wire, and bad layout.
They need to be tied together in a way that they are “blocked” together so they don’t bend at the solder points, and routed across to the opposite side of the PKE body to minimize the bending.
You guys need to brush up on wire layout.
I’m guessing the wires are breaking at the solder points to the arm.. Yes?
Copper has a cubic crystal structure and bending a copper wire “work hardens” it, which introduces defects known as dislocations into the structure (jagged crystal shapes). Basically, the more you bend anything copper, the more brittle it becomes. And that is happening to the end of the wires every time the arms move up and down.
Yeah thick wire, and bad layout.
They need to be tied together in a way that they are “blocked” together so they don’t bend at the solder points, and routed across to the opposite side of the PKE body to minimize the bending.
the hyperdyne boards have hot glue on the termination points to stop them from moving when the arms move. that way the solder points dont break. also, the wire gauge actually pretty thin, but the pics seem to make them look bigger than they actually are.
Does Hyperdyne supply twisted or solid wire? Honestly, I’d just drop a few gauges and forgo soldering in lieu of wire-wrapping.
I do not have it with me right now TJ, but im 99.99% sure its solid.
This is what I was commenting on. The wires connected to the arm board. Those could break with use if left like that.
Broke my second servo. I must just be stupid. Where the wires connect to the PKE Wing keep getting caught on the main board and puts the wing in a bind. If I can’t get it soon, I might pay one of you guys to put it together for me.
I’d be glad to put one together for you.
I’d be glad to put one together for you.
How much would you charge?
Nothing… I’m not supplying any parts other than a little solder.. I don’t really charge for my free time. :3
But I do have a tips jar. ![]()
And I can always use the build pictures for a tutorial to help others with their builds.
I have most everything in the meter, I just can’t get the servos right. PM me so I can get your address and Paypal, I will pay you something for the work.
