Super Noob-ness Questions Help-ness

Alright. I -really- want a Pack. I know I’ve made topics before about making a pack but those plans always fall through and I become a sad panda.

Now.

I’m thinking about buying the parts and constructing them; I have no tools, or workspace. So it’ll be a little hard. However if it DOES get too expensive; I will have to make the parts (So far the only thing I really see my buying completely is the Neutrana Wand..since I’ve got no idea how to do that, Lol.) and work from there. I’ve actually tried Norms plans once but having no idea what the hell I was doing, I kinda slapped that on hold.

Sooo:

  1. What’re some cheap alternatives for certain parts?

  2. For someone with limited space, what should I do for a work environment?

  3. Since I’m not a cardboard aficionado, what would be a good, cheap material to make the rest of the Pack with?

Well…how cheap is “Cheap” I am sure you have seen the “dollar store” packs before. I have honestly seen some cheaper packs look better than some packs that people spend more money on. Honestly, my opinion is that the thing that is expensive is all the details on the pack. If you are willing to not have an accurate pack you can make one for very cheap. I made my whole pack out of foamboard which would cost you less than $15 for the amount needed. The reason my pack cost so much is because I started buying tons of little things for more accuracy. If I could start over I would make my whole pack out of styrene, which if you can find a plastic dealer near you, you can buy a sheet for less than $50. Both foamboard and styrene can be cut with a box cutter also. My whole pack was put together with hot glue and amazing goop. Good luck man! Just get a material, start measuring, and start cutting. By the time you paint it black it will start looking good.

Hmmm, Well I don’t want like, DID YOU STEAL THAT FROM DAN!? Accurate, but Accurate enough. 75-80% accurate is fine for me.

But thanks for all the feedback with the plastic! I’ll consider it when I start laying out my options on construction.

Granted, I am still new to pack building, but I would think a lot of the accuracy comes from the details. For example, for all my connectors I just went to home depot and threw a bunch in my cart and used them. Your other option would be to pay twice as much (maybe) and try and find them online. Also, if you dont go all out buying resin parts and just use your imagination you can save some money but loose a little accuracy. For example, for my clippards I just used 1" PVC and put a washer a knob on top. Also, for my detailing on top of my booster frame I just used some wood detailing from a hobby shop and glued them to foamboard.

Most of my work has been done off the tailgate of my truck. I don’t have access to a garage right now and though it’s sometimes lower than I like I sometimes pull up a chair.

As far as monkey said, once you paint it black…YOU START HEARING THE GHOST BUSTERS THEME SONG AND BEGIN TO DANCE AROUND!

Ahem…or was that just me?

So, I have a noob question…which comes first?

1-Mounting pack parts to mother board

2-Mounting mother board to alice pack

Also, whats the easiest adhesive to use to mount pack parts?

I’m making a junk pack, i’ve seen Goop listed on some places, just not sure on what to get.

Mount the alice frame to the motherboard first.

I would suggest the 5 min epoxy or good old JB Weld.

Well, I mounted my stuff to the mobo first, but then my pack is not 100% accurate, either..so that being said, it may not be possible to do this if everything is the correct size, and in the exact location it is supposed to be? Then again, there are people who seem to make packs, remove them from the frame, and sell them with no problem..

I think your best bet is to get your mobo, drill your holes where you’ll mount it to the frame, and then check as you’re attaching pieces to the mobo. Just make sure you pay attention, and you shouldn’t run into any problems.

Thanks for the help guys! :cool: