Sorry to hear about that MagicMan. As of right now, I’ve disconnected a few wires on the internal part of my wand. Strangely enough, nothing appears to stopped functioning, other than the sound.
I imagine that some of these are safety wires, that program the tip to return to it’s normal position, or to turn the gun off after a certain amount of time. Of course, I just might not be noticing the effect immediately.
I can confirm that the vibration motor is indeed connected to the extending tip! It’s unlikely to disable one without disabling the other.
I’ve managed to place the cogs in back in place using deductive reasoning. Tip still extends but now, like many others, it is horribly out of alignment and often goes in and out multiple times.
It doesn’t do this upon initial flipping of the switch, but in whatever position the tip is in when I first activate the wand, it does go up and down until it gives up. It could be up or down when it’s finished. Placing the wand back into it’s proper position, then pushing green lever activates it properly, but when ascending the tip, it again sporadically goes up and down.
I’m unable to put the body plate back on as the cylinder with green wire needs to be completely removed before I can adequately put it back. It’s been a long night and I don’t have the patience to do some plastic surgery on the tip without seriously damaging it or myself.
I put hex nuts in the similarly shaped hole left by the fake clippard. The real brass barbs screw in perfectly. The horrible rubbery end piece was removed with a metak band added, a new tip added and the whole area sanded to match the acrylic pieces.
The clippard now has a real label and real brass thread knob added. Also, added a white hat light instead of the odd black nubbin. Much more to come plus painting.
I hate to bring up a guy everyone here hates, but VB seems to have figured out how to get the gun sound to a pack. Of course he won’t say how so I have to ask if anyone has an idea how to hook it to something like a mini ipod speaker or something to that effect? I pluggedone but only got that pop sound when flicking a switch.
It’s possible that he could’ve just faked it with some video/sound editing, but if he actually has, it seems pretty reasonable to guess that he just put a speaker output into the Pack and extended the wires that would’ve gone to the speaker in the base of the Proton Gun.
As has been remarked on in past posts, the jack at the end of the handle doesn’t actually carry an audio signal.
If you want to bring the sound from the gun into a pack, simply open the gun, solder a wire on both the positive and negative leads from the speaker in the gun, knock out the jack in the rear handle, and run the wires through that hole, down the loom into the pack, and solder the appropriate wires to their appropriate posts to a speaker in the pack.
I haven’t watched the video since it came out but I think Bob has only attached the gun to the pack. No running of wires. Doesn’t he say something about about having the sounds from the gun and also from the pack?
so no mods for it. He just attached the gun to the black wire loom, definitively not a Ray or Egon difficulty job! :sigh:
By the way, it can be a nice idea to have a “complete” Matty set, but I wouldn’t pay him 2000$ for a (overpriced) 600$ pack and another 800$ value Matty toys!
Upon reading here of the readily available fitting by which one could attach the loom hose to the Matty wand, I set off for the nearby Home Depot, wand in hand, and decided to grab myself one or two. I got plenty of looks from staff and shoppers alike, who wondered what the hell I had in my hands… but anyway… I came home with 3 different fittings.
All of them work, but with varied results. You can choose the one that you prefer, but I feel there’s definitely one that works best; the one I’ve got the hose attached to in these pix. Reason being, you can put something around the end of the hose itself to keep it from slipping out of the fitting. Tape wound around the end, a cable tie… whatever. The smallest will allow you to attach the hose to the outside surface of the fitting… but will (I think) leave it looking somewhat sloppy. The other, wider threaded post will allow you to slip the hose into it, but it’s actually too small, and compresses the loom hose. Whatever.
Anyway… a little bit of paint, and it’ll be all good.
Well I have been following this thread for awhile now and am at the point of moding my own. I have three of these bad boys I need to convert to our packs. I’m hoping some one out there has pictures of the darned things open, it would be a HUGE help. I am going to be honest, I am going in blind and terrified I am going to mess these things up. Any one have some advice?
I went by Home Depot earlier this week to pick the coupling DekaPrime mentioned in his post (1 1/4 diamteter) and it didn’t fit the end of my wand. It just a bit too large to fit snug on the small lip at the end of the wand (behind the hand guard where the 3.5mm jack is). When I went back to return it I grabbed a 1 1/2 inch to try and fit over part of the handle grop but that just a hair too small. I tried to find the couplings that MadKidJedi posted but couldn’t find them. Did I grab the wrong one or not put it on right? Is there another alternative other than making my own out of PVC? At this point I’m tempted to just ziptie the hose I bought directly to the end of the wand. I’d like it to look better than that, but not sure what else would work.
Edit: I brought my wand to Lowels and found a 1 inch adapter (1-In SCH40 Adapter 474010, item # 188224) that fit it perfectly. Tight enough to hold fast to the end of the wand but not to much that it can’t be easily removed. Sadly the hose I bought doesn’t it the end so I’m going to have to modify it but cutting off some of the excess tubing around the end of the hose and using a zip-tie to connect it to the adapter. Once I get it painted I will post a pic.
Oh, snap… sorry, amigo! Didn’t mean to send anyone on a wild goose chase. I sent the part info a few weeks ago to a fellow GB local to me, and as such, have that info at hand. I got my adapter at Home Depot, in the plumbing fittings (obviously), and the UPC code on it is: 012871625954 and the description from the receipt is 1"x 3/4" PVC FEMALE ADAPTER $0.97. Hope that helps..!