Just curious on where or who u got your v-hook from? I’d like to get one to fit my wand.
What type of piece did you use for that?
The 1 1/4 inch piece of PVC should be about 1 1/2 inches long and the 1 inch piece of PVC should be 1 inch long. Then glue the pieces together with PVC cement or epoxy. One end will have a 1/2 inch recess to accommodate the end of the thrower and the other end both pieces should line up together. I painted mine with Krylon satin black paint. on the recessed end I ended up wrapping some painters tape inside the recessed area until it fit snug and wrapped the end of the split loom the same way.
in trying to take it apart. it seems as though, some screws that are holding it together are covered with caps to cover the screwholes
I have completely disassembled one and you have to drill out the plugs with a 1/4" drill bit. They are glued in and can not be popped out.
I cant seem to find the screw keeping the back portion on.seems the two pieces are stuck together near the slo blo box
Did you remove the 2 button headed Allen screws from the underside of the instrument bar?
I did, seems as though they plastic welded my slo blo tube shut. It doesn’t want to budge
Any chance to see some pics of the wand disassembled?
I’m starting to do the same on the banjos using Model Master Enamels, but I fear the paint will flake… Did you use some primer?
I used Model Master enamel paint when painting my banjos. The paint sticks quite well and has not flaked off.
So has anyone figured out a way to activate the pack with the matty wand? I’m looking at a new build in the spring and i’m thinking of using a Matty wand instead of building one but I don’t want to have a secondary activation for the pack. Kinda want some one stop shopping;)
Having trouble get the camera to focus but here’s the start of some mods to the wand.
Added a hatlight instead of the black nubbin. As for the Clippard, I added an original foil label. Also, took the top off the Matty Clippard and added an actual Clippard knob with brass thread.
Pics please!
The light when you fire has stopped working properly on mine. It sometimes goes pale blue or not working at all. Everything else seems fine. Wondering if it’s a loose connection. Tempted to open it up and have a oke around. Anyone else had this problem?
I guess if you could figure out how to utilize the trigger tones from the rear stereo jack, you could run a lead into your pack lights.
My wand is having that problem where the main power switch causes the barrel to go in and out.
I added the wand to my pack. My intention was to not modify the wand in any way:
Anyone try to disconnect the vibration motor. It really kills the sound.
Doesn’t look to bad to me. I’m gonna start my first pack build with a studio creations she’ll so I think this wand will be a good weight for it. I’m hopping anyways.
Okay. Opened my wand up tonight.
When I removed the screw plugs that cover up a majority of the handle, I had the intention to keep these screws out and resin the gaps so that I’d get a smooth surface and could still open the gun if I ever wanted to make additional modifications.
Well, some problems were run into…
The cylinders where the 3.5 mm and the green tube are glued on to the gun. The 3.5 mm is only a minor nuisance, as you can still pull the bottom handle clear of the gun. Unless someone found a better way, you pretty much have to destroy the top part of the cylinder where the green tubing is to remove the bottom base of the gun.
That wasn’t really the problem though.
I was trying to be ever so careful while removing the little bits and pieces of the gun that I accidentally had the plastic cogs come loose! They scattered over my worktable and I’ve tried every configuration I can think of to put them all back in. Any pictures of the cogs would be appreciated.
It also appears that there is no way to disconnect the vibration motor without disconnecting the extending tip; as they are run on the same motor. Theoretically, you could remove the spinning bit or a single cog and the vibration piece would be quieter but you’ll still here the motor inside that works the tip and ■■■■■■■■.
Though, this is purely based on the fact that I have one single cog turning while the others do not. I’m quite certain more has happened to my gun than what I know.
Again help would be appreciated.
I got two guns, this is pretty much my, here hold my gun prop; so it’s really all right if I don’t get it working again.
But I’d like it to work somewhat.
The tip of mine has stopped lighting up at all now ![]()

