My gb_dan Ecto Goggles build up thread and tutorial

Feel free to use this post as an official gb_dan build up thread if you guys feel like it! It’s better to have all the resources in one place for future builds!

I got my goggles and I am rushing to get them done for a small con this weekend! I am trying to document as much as possible. So far it’s taken me a few hours to get them done.Half was done last night (cleaning sanding, etc) and the next day was for painting. I could have been done with them today but will wait until tomorrow morning. Most of the time was removing the excess flash. Besides that, there is not much more to be done, other than applying some primer and paint!

The lenses were already painted, and the straps had the buttons already attached. Thanks to Dan for that! Oh, everything was nicely packaged and very well protected. Kudos to Dan.

Well, I decided to get OD for the goggles. I went to Home Depot to no avail, so I went to a Hobby Store and got some Tamiya OD paint. Keep in mind that I am a completely newbie with the airbrush. I’ve only used it once or twice many years ago… so I sat down, watched a million airbrushing techniques/training videos on Youtube and decided to give it a try again. I am happy to say that it came out real nice! I wanted to mix the OD with a little white, but realized that I didn’t have any, so I went full OD green.

I gotta admit… I was having so much fun with the airbrush that I decided to also paint the knobs, and fix some over weathering I did to my trap. If you haven’t tried it, just go and get yourself one. It’s awesome! I just don’t think I’ll be back to rattle cans ever, well, unless is a big project! Oh, not to mention that airbrush paints dry FAST! When I weathered my trap I think I went a little overboard with the weathering, and wasn’t completely happy with the result. A few seconds latter with the airbrush and I was happy again with my trap! I’ll still add some weathering, but will go a little less aggressive. There was no way I could had fixed those spots on my trap with a normal spray paint can. Time to go back to Home Depot and return that Hunter Green rattle can!

Here are some progress pics:

This is how the goggles will look out from the box. I had position number one on the non pre-order list, so this is pretty much how you will get yours. There is some flash removing and sanding to be done. I used a Stanley and X-acto knife to clean them up. For reference I used photos posted by members who got theirs cleaned by Dan, just to make sure I was staying inside the line when doing my cuts.

image

image

image

image

image

This is normal stuff with resin models. A little bit of epoxy putty should take care of it.

image

image

Most of the cleaning process has been done!

image

image

image

image

image

image

image

Getting ready to drill the holes for the lenses.

For this I created a template using the lenses provided by Dan. I just traced them and cut them with an X-Acto. I folded the circles to find the exact center point. I taped them to the lenses (I also used a laser guide to make sure they were both aligned) and made some pilot holes in order to use the Hole Saw attachment. I wish I had a drill press! :slight_smile: Oh, make sure to use a smaller hole saw. One hole was a tad too big for one lens, but it was an easy fix. I was going to use some epoxy putty, but then realized that the rubber gasket supplied in the kit, when in place will cover the hole, so I will add some two part epoxy on the back and secure the lens in place. I’ll take pics of the process… my English is not that good :stuck_out_tongue:

image

image

image

image

image

Cheating with the laser guide :stuck_out_tongue:

image

image

image

image

image

image

Airbrush time! Can’t believe how different the color looks when inside/outside! Please keep in mind that I had only airbrushed a layer or two of paint. You can still see primer spots. I was still experimenting with the paint/thinner ratio. I added another layer after that and the result came out much better.

Indoors

image

Outdoors (sun light)

image

image

I also finished cutting/painting my gizmo holder

image

And here are some photos of my trap with a little less weathering. I got airbrush happy and also painted the front display (haven’t attached it, yet) :slight_smile:

image

image

image

image

Feel free to use this post as an official gb_dan build up thread if you guys feel like it! It’s better to have all the resources in one place for future builds!

I like the paint you used better than the Italian Olive I found at Walmart. I’ll have to get some of that, and it will be an excuse to finally use my air brush. :slight_smile:

Looking sharp Jose I’m really looking forward to the finished product! :cool:

Thanks to both of you guys!

Dan: I used the Tamiya OD. I really like how the color turned out! I bought a Hunter green spray can, but I really wasn’t looking forward to paint them in that color. :slight_smile: I’m telling you, you’ll never go back to rattle cans!

Dimitrios: Thanks a lot! :slight_smile: I’ll have them ready tonight. Will definitely post pics! :slight_smile:

Does anyone knows where the envelope label goes on the goggles?

Here are the most recent pics:

image

image

image

image

image

image

image

image

:slight_smile:

Looking great, JT. :slight_smile:

Wish I could find those screw-based Snaps, would make my job a lot easier.

Thanks mate!!!

I’m also having a hard time finding those screw base snaps… for the time being I used the resin ones, until I find them. I have normal, tapping buttons but I’m afraid I might crack the resin installing them. I’d also like to add some buttons to the side as well. I was checking the HD screen caps and there are definitely at least three more: 2 on one side and one where the black label is, yet I still haven’t figured out where the envelope labels go… argh! LOL!

Envelope labels?

Yep… according to namebrand’s rub down transfer sale thread, he mentions: “Some of the graphics were also used on side of the Ecto Goggles (the “envelopes”).”

When I ordered mine, I also ordered a set for the goggles. Now my goggles are almost done, and I have no idea where to apply the “envelopes”.

I believe the ADF/TR G/ TR/ Off graphic may be one of the ones he’s referring to (if it is, it would be placed where the power switch would go). I’d suggest PMing him to enquire about it.

Will do :). Either way, thanks a lot for your thoughts, man!

As soon as he gets back to me, I’ll post the info.

Isn’t it just a standard male snap piece with a little screw through the hole in the middle?

When I made my belt clips, some of the leather was too thick to work with a standard snap once folded over. To solve this issue, I put a leather rivet through the hole in the snap (and then through the 2 layers of leather) and attached it that way- similar to the way it looks like Dan has the screw through the snap hole.

Yep! That’s the one!

Thanks a lot for the tip! Good idea!

Just a standard snap with a screw slid through it? Hmmm, I’ll have to keep that in mind if I break one of the frames hammering the base part of the snap.

Cool, lucky guess on my part! I may have to do the screw-snaps on my welding goggle frames (they are a hard plastic) as well; I attached the snaps with their normal backing piece, but one of them might not hold up to use.

BTW, great build-up JT! Did you use the airbrush to weather the green paint on the frames?

Also, here is the placement of the envelope labels (namebrand added it to his thread after people were asking):

image

I just learned something new…

Thanks!!

That tip will come in handy on a number of projects I’ve got planned.

Thanks mooslug! :slight_smile:

I didn’t weathered them that much, but I decided not apply a clear coat, so they’ve been getting a bit of weathering/scratches on their own. Hehehe

Snap fastners:

http://www.lowes.com/lowes/lkn?action=productDetail&productId=45334-355-45334&lpage=none

They’re mostly used for convertible top covers. My Caddy has them.

Thanks a lot for the link, Rick!

INCREIBLE, love your trap man!!! Love those googles! Hope mine arrive some time this year.

Sal