My second scratchbuilt Pack

That is simply amazing work. Keep it up!

Nucking Futs ! Awesome awesome job sir

Thanks a lot for the compliments, thats music to my ears :slight_smile:

Alright, last time i had the upper and lower sections of the pack almost finished so what had to come next for me was joining these two big parts by making the center cover.

So i cut one piece of styrene to the correct shape and test fitted it first:

Then i cut it up into three sections to get the different heights, cut out some wall pieces too, glued it together and ended up with this:

Next i had to glue it either to the upper or the lover part but i choose the lower part. To make the whole thing look like one piece and get rounded corners i just did what i always do if rounded corners are needed. Basically i smear filler into the corner and pull a screw or another round part along the corner. Then when the filler is halfways cured its pretty easy to cut of the excess:

A seam done with method should like this (or better) even without any sanding:

Of course it will look better with some sanding tho:

As you can clearly see the cosmetic plating on the spacer was already glued in place too when i took these pics.

Here im test fitting the whole thing to the upper section:

Looks like a tight fit :slight_smile:

After taking care of the corners and some sanding it looked like this:

And that´s it…im done :smiley:

Ok, the fake weld on the N-filter is not there in these pictures but i didnt forget about it. Right now the first paint is already drying on the master and i´ll have some pictures of the painted thing up soon.

Oh..another thing i wanted to mention…does anyone have any ideas or suggestions about what i can do to make it better / more accurate ? Please let me know, im not afraid of ripping pieces off and redo them ^^ Actually i already did that a couple of times, lol

More to come really soon again.

jesus thats beautiful

my only suggestion is since you seem to like adding the small curves and drafts that are evident on the pack, there is also an upward slope between the gunmount block and the crank gen, right where the HGA goes. other than that, this pack is pure Sex

you can see it here on the planet hollywood Minnesota pack.

No words. They should’ve sent a poet.

I’m harder than a diamond right now.

Great, thanks for the input kind :slight_smile:

I was hoping to get some info like this from you since i know youre paying a lot of attention to detail. Consider it changed and done, hehe :slight_smile:

That is one beautiful Proton Pack.

Man you are rocking out this pack in record time. Quality didn’t suffer a bit. Awesome.

Wow, that looks like a masterpiece. I wish my build would look like this, but I don’t have your talent…or the right tools.

Btw. from which part of germany do you come from?

Oh baby.

Thanks for the feedback guys :slight_smile:

Oh, you dont need a lot of fancy tools to work with styrene, i made this whole thing on the floor in my living room ^^ You just need a sharp knife, some rulers, a lot of sanding paper, a sanding block, maybe a few files and some other small things. Sure i used my dremel too but not for anything that could not have been done with files or sanding paper. It is really not very hard to work with this stuff if you´re patient and take your time with every single measurement, every line you draw and every cut you make. :slight_smile:

I live in Schleswig-Holstein, pretty close to Rendsburg.

German high-end builders: Audi, BMW, Mercedes, Maybach, Bigi71.

Grrrrrrr…what are you doing to me kind, haha :wink:

Shame on me that i´ve never noticed this detail before, lol. But i think i fixed it after looking at all reference pics i could find of this area and double checking where the hga sits. Im glad i still have all the pics taken by thegreatgallina, one of those was especially helpful :slight_smile:

The result looks not too bad i think:

Im sure ill have more pics of my progress soon but for now here´s just a little teaser shot of the whole packshell as it is right now:

And for those of you who are curious about what it looks like from the inside:

Last time i forgot to upload this pic but i already had it so why now show it :slight_smile:

Its a pretty strong thing actually…so i hope it doesnt get destroyed when i demold it. Molding will have to wait for a bit tho because im poor and silicone is not cheap. Anyway, the good thing is that i can now finally clean up the horrible mess i made in my living room, there are little styrene pieces everywhere on the floor ^^

More coming soon :slight_smile:

You’re making shells from this? They will sell like warm buns! :smiley:

It really is a masterpiece mate.

Thank you Nick :slight_smile:

Sure thing, i sort of have to make some shells from it because its the accurate material and a couple of years ago i said to myself that if i ever make a pack again it has to be fiberglass and aluminum. Im just not sure yet if im gonna sell them…well…we will see ^^

Of course i missed the white light caps in the for sale forum ( :lol: ) and since the buck for the pack is done too and i had nothing better to do i decided id like to try what i had originally planned for the hatlights. Which is making them from scratch.

I did it with a much more ghetto approach than CPU64 tho :slight_smile:

So what do you do if you need a round part like a hatlight ? yes…you use a lathe. Well, i dont have one but i have a dremel so i used it as a makeshift lathe like this:

The material i used for this one is milky white acrylic and “turning” it with different drill bits works very well if you are very careful and dont do it too fast.

Still unfinished and unpolished but it already looks kinda like a hatlight:

Now a pic of the finished thing:

The metal part fits in there very tightly and stays in place without any glue:

And finally a picture of what it looks like when its lit by a warm white LED:

It took me half a day to figure out how to make it, but i hope the other two i still have to make arent going to take that long. I already have some opaque orange acrylic so maybe ill try to make an orange one tomorrow.

Now you’re just messing with us. Making your own Arcolectric caps by hand? Holy ■■■■. :shock:

I bow to styrene god.