Newbie foam build. Help!

Hey guys!

First of all, thanks for all the material in here! This website is great!

I have been a GB fan for a long time. When I was around 10 years old I built a proton pack out of some cables, shoes and medicine boxes, butter cans and cardboard. It looked horrible, but I certainly did have lots of fun with it!

More than 10 years later, by coming across this community, I decided to give it a shot and try to build another one, a little bit better this time, but not even closely as accurate as you guys do around here. I have little money to spend on it, so I am trying to keep it as simple as possible. Also, I’ve never done any kind of work like this, so I am not expecting much of myself either. I don’t mind if the result is not very accurate, as long as it looks nice enough.

I decided to go with foam, since it’s cheap. I am building it from scratch trying to follow Stefan’s plans, but my tools (including the one above my neck) are not so great, so it’s being hard to get all the measures correct.

Even harder is to get all the edges cut correctly. I don’t have a tool to cut foam so I am just using a heated knife, then sanding the edges. I am planning on using wood putty to correct the irregularities make it more smooth.

Here are some pictures of how it’s going so far:

I have the impressions that it’s coming out way too small. Does it make sense?

I get the feeling that the pack’s supposed to be bigger from the pictures I see around here, but maybe that’s just my impression.

Another thing: I got flat black paint to cover it, but I am afraid the glossy should be better for a more metallic look. What do you guys recommend?

Any suggestions on cutting/sanding the parts and using putty?

Please give any feedback/suggestions you guys may have!

Thanks a lot!

I too was surprised by how small the packs really are. It’s hard to tell without something to compare it to, but ratio wise I at the most would say that some things look like they could possibly be taller, but again, it’s hard to tell without seeing a ruler on it.

it looks smaller because you’re missing some cosmetic plating, the gun mount box and the powercell, when you get them it’ll start to fill itself out.

so far so good!

As I’ve been building my pack, everything has seemed really small. But, once I had enough parts together to do a test fit, it looked great. The wand was the most surprising part. The main box is dinky!

Thanks, guys!

With the gun mount it already seems bigger indeed!

Makes a big difference.

I have a question for the other foam builders out there: what’s the best way you recommend to paint the foam?

Should I use primer? Cover it with glue before painting? Paint it straight with some foam paint?

One more question, this one to all builders out there: what’s the easiest way to get the lights?

Preferably one that doesn’t require soldering. I am fine if it it’s not 100% accurate.

Is there any simple LED kit that does already what we need for the pack lights?

Thanks!

I’m working on a foam project right now myself.If you haven;t glued these together yet, elmer’s spray craft glue is foam freindly, and you could glue all these easily with one small can in probably 15 minutes. other spray glues, even though tye might say they are for foam, could melt them. Test first!

You’l want a harder skin on these to prevent dents and damage. I only used flat water washup house paint originally, but am now using a one two punch.

Fill issues with elmer’s wood putty from walmart. Its foam freindly, and sands easily. next, I’d add a few coats of home made gesso. I use a mix of 2/3rds a cup of premix joint compound, and 2 cups of elmers all purpose white glue (from Lowe’s or Home depot) you can get gallon containers of the stuff the cheapest there.

Mix that with a hand mixer for a few minutes, and put on a few coats, letting them dry completely before the next coat.

This gesso is NOT waterproof, but gives you a hard surface to work with. Sand again, if needed, and then apply a few coats of satin or gloss water washup latex house paint. (Just get black, and your surfaces will be done when you coats are done.)

You can dull down the house paint surface after drying with sandpaper if you like even further, but the semi gloss and gloss house paints have a harder finish to them.

You should create a cutout where the cyclotron will go, so you have hollow space under it for lighting or electronics. Do the cyclotron the same way, with hollow rings, and a solid mdf or foam core “cap”. That way your cyclotron lights won;t have huge thick foam discs around them inside.

T attach all this to a MB, cut out square cuts on the bottom, predrill mounting holes, and then glue them into the foam with gorilla glue then just use slightly larger wood screws than the predrilled holes to secure the foam parts to the motherboard.

(This way you can replace them, or remove them for upgrades or future work easily.)

You also want to do the block cutouts, and pre drilled areas for wire and hose connections as well.

My builds back in 2009 were 50% insulation foam, and they still look exactly the same today as they did when completed.

Thank you very much for the help, Gareee!

I have been using regular wood glue to glue the foam pieces together.

So far it’s worked well, do you think I should get the foam glue instead?

I have some plastic wood filler at home, do you think this will do in place of elmer’s wood putty to fill the issues?

The gesso idea is new to me, interesting.

I was considering using bondo for a harder skin. I liked the results KC got on his wand with bondo (http://www.gbfans.com/community/viewtopic.php?f=2&t=21827#p266280).

What do you think about that?

Thanks for the tips on drilling the holes for the hose connections, I had not considered that!

Anything containing chemical drying will eat foam.

Thats why I avoided bondo, and many resin surfacers. Plastic filler also might contain chemical driers in it. If its water washup, you are ok though, from my experience. Since it looks like bondo worked well on his foam parts, you could get some and try it out on a scrap. Different insualtion foam manufacturers us slightly different chemeical compositions, and you can;t always get exactly the same brand you bought before, so I test everything now.

(Someone said DAK contact cement was insulation foam safe… I put some on a bit of the green stuff I’m using now, and within 5 minutes it was a puddle.)

Woodglue will work, but wood glue cures with air contact. Since the foam is porous, the center will dry eventually, but I’ve read horror stories about people trying to work with foam, and finding the centers still uncured after a week, and coming apart. the spray glue is tacky instantly, and you literally have a workable bond in a minute. I glued and carved a part just a few days ago, and from glue to final foam carving, it was done in about an hour, including glue and carving time.

Since you won’t really be carving the center dryness isn’t as important, and it will dry over time most likely fine.

(I rarely have the patience to wait 2 hours for gorilla glue, and can’t stand waiting overnight.)

You can buy gesso, but its not cheap and it does give quite a hard surface. But if you make it and mix in too much joint compound, it becomes brittle. Google “Monster Mud” as well for some additional recipies on what people use for durable prop building. the closest somewhat flexible recipe I saw was on teaspoon joint compound to one tablespoon white glue… I just upped the recipe, favoring the wood glue for the flexibility.