Pack Overhaul - Movie to Real Ghostbusters

This should be fun..even if it doesn’t turn out good…The Goal is to totally modify this budget pack/vac shell and turn it into a halloween display. In this case, we are going to turn it into a Real Ghostbusters pack.

Here’s the plan.

The HGA is gone. The Injector tubes are gone. THe Booster and frame are gone. Filler tube gone. The ‘clip’ part that the gun attaches to, that overhanging square will be cut off. The boxy part below the Crank Generator will be cut away and replaced with that yellow pipe.

I might cut square holes in the Ion arm and add yellow lights if I can figure out how without ruining it. It got gutted today, work will start tomorrow… first up..sanding. lots and lots of sanding :slight_smile:

This should be interesting… I look forward to seeing it.

First step: Tear off sticker on bumper.. Fill two drill holes for centerpiece..sand down as best as possible, and prime.

Same goes for the R331 piece. Take off sticker…sand down, and prime.

Once those start looking good, bumper and piece starts getting painted silver.

Second step:

Remove Booster.

Throw out booster frame.

Throw away busted NFilter…

Start Chipping away at cheap spacers…

Third step.

  • sand, sand, and more sand. Might even use the sander attachment on the dremel.

  • Cut pieces of wood to re-inforce holed area by power cell lights

  • fill in holes with apoxie.

  • remove filler tube and circle beneath.

Fourth step .

Keep gun hook area, cut away bottom square beneath.

-Replace with huge PVC pipe to stand in for Yellow part. Find some kind of plastic bowl for the curved ‘top’.

  • Find hose wide enough for grey hose surrounding it.

  • Find PVC pipe big enough for booster

  • buy small tubing, paint silver to create RGB ‘frame’ for booster.

The only thing I’d like to work better is the Ion Arm. It’s not big enough, and I don’t have the wood cutting abilities to make one with curves…but for the rest of the pack, that is the current plan set…

Original state of gun..

Filled in holes, removed labels, and got rid of sucky light bar guide. Took out lights so I can trouble shoot what is wrong…

Big holes start of fill in. I decided to ditch the wood backing as all of our jig saws are either out on the job, or missing totally. Epoxie start will have to do..

I think the biggest problem will be trying to figure out how to cut out the middle section without damaging the rest…so far it’s going along rather well

Sanding, painting and priming! I think that part, if I’m going to keep it to round out the pack, would look best in red to go with the booster..

.

A little work with the dremel gets all the balsa wood off the back. far faster than sanding..

A little test to see how the gun body looks in real ghostbusters glue. I’m going to try and remove the handles so I can reposition and repaint them…otherwwise, it’s going to be tough to block everything off for painting..

Personally, I’d think a darker blue would look better. That bright blue gloss just doesn’t do it for me.

But hey, it’s not my project.

did you flood the gun?

Looks like he dunked the gun into a bucket of paint.. I couldn’t spray paint like that even if I tried…

I could.

it was a tad overkill, wasn’t it? ..like I said, this wasn’t meant to be anything final, just a quick spray to see how it looked in that color.

Sears didn’t have anything darker blue on hand, and they where all in gloss…RGB is more of a night blue color, for lack of a better term..

Same goes for the red. All they had on hand where Satin and Gloss..although it almost looks like a neon red. will have to hit up home depot and see what they have.

I used a satin burgundy color that came out brighter red than I was expecting. The end result looks pretty good.

Even for a test spray that is way way to much paint. For the amount of work you now have to sand the gun down and get it nice and smooth again you would be much better off spraying on card or something of that nature in a small spot and then just placing the card on the gun to see the colour.

I apologise if this seems like a dig at you it’s really not, but you are causing yourself more hassle than you need to.

image

My god dude, your spray paint learning curve is just a completely flat line, isn’t it?

1 Like

I can’t imagine that amount of spray paint being a “quick” spray.

It’s not only a flat line, it’s become quite demonic…

Sometimes it turns out passable, other times it turns out like a care bear puked..

New colors

[img]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-snc7/301464_10150432523560211_530260210_10794383_2139672816_n.jpg)

Also keep in mind this is meant as a cheap halloween decoration…Something to put outside for trick or treaters to ooh, and ahh at, and adults to most likely ■■■■■. If it falls over and breaks (most likely) or worse, gets stolen, it’ll be no big loss than putting something better constructed out there…

I’m not trying to hate at all, but all I can say is that when it comes to spray paint: “Everything you are doing is bad… I want you to know this…”

I’ve posted it once, I’ll post it again.

Also, I made you a present, Shredder.

the finished product.. minus some tape still in place at the time to hold the part in place for glue to work..

Hate it if you will…I’ve stopped caring ;o)