Im starting a SC shell pack and I have the MMM motherboard. One thing Im stumped on though is the board seems too pig or the shell is too small? What have others done to remedy this issue?
Some parts do/can stick out a bit but you’ll have to cut/grind down any major overhang.
How much of a difference is there?
Everyone will recommend making your motherboard fit your pack, and not the other way around.
about 1/2 an inch on the bottom. though maybe thats for the cosmetic plating that goes around the bottom of the generator?
Here is a great thread on how to make a motherboard for your shell. Obviously since you already have a motherboard you would just trim it to fit, but the thread will give you an idea on how it should fit.
Also if you need to add cosmetic plating on, do this before fitting the motherboard.
You can see here I spaced it to line up even all the way around. Maybe just some screws nuts and washers is all I need then fill the gap with bondo? It isnt off too much when you look at it like that.
I would connect the two halves to have a more solid shell. Then take a sharpie and trace the top to show the new line on the MOBO then cut/grind it down. A little more labor intensive maybe, but you won’t have gaps to worry about filling in. Especially if you are going to have wires inside for lights.
I personally would just get some wood and make your own motherboard like the stunt packs were.
No sense in using an expensive aluminum motherboard, and then shaving away a bunch of it.
Another thing to use that is inexpensive is to buy a sheet of fiberboard (like the the back of a clipboard) trace you shell and like AJ said cut a fresh one. Save the Aluminum one for a future fiberglass shell…
Thanks for the advice. Ill see what i can do about a new mother board.
Will 1/8 inch plywood work for the motherboard? My father-in-law has a bunch of it.
Sent from my PC36100 using Ghostbusters Fans on Android
Ok So I tryed the wood idea with no luck. And I am not sure where i can go to have a custom aluminum motherboard made that wont cost me 100’s of dollars. Im getting quite flustered with trying to build a pack. Seems like so far both attempts at building a pack have totally bombed. My scrap build pack became way too heavy and didnt look right and now my studio creations back and MMM mother board wont fit each other. Nothing against either company I just cant seem to make this happen.
Dude this field is all bout customizing, why can cut a piece of wood?
Buy yourself a 2ft x 4ft x 1/4" thick piece of MDF (Medium density fiberboard) you can get it at Home Depot (about $5)
Trace the MMM motherboard out on the sheet with a fine black sharpie, remove and lay out your SC shell and tweak the fit, remark the “actual” lines in red and cut. The MMM motherboard is made t to Stefan’s plan specs and is a standard measurement, I know from others that the SC shell can be a bit small due to vacforming and requires adjustment.
Good luck with your build.
I kinda dont want my mother board made out of wood. Id like to do it out of aluminum. Even though its a vac shell I want it to be some what close to the real deal.
I’ve been thinking about this too for my SC build. At first I did plan on going aluminum for the mobo knowing that most mobos out there, as far as I know, are not a great fit for SCs,.
I wasn’t looking forward to spending $50+ and then hoping I don’t mess it up as I try to get it to fit. But after a year of working on this pack, I’ve amassed a nice sampling of MDF sheeting! Can’t beat the price of free leftovers and the ease of cutting. Once its painted black you’ll never notice.
I’m hemming and hawing if I should use more accurate 1/8" MDF or go 1/4" to make it little sturdier…
The thing I’d do is make your own aluminium motherboard. Since you dont wanna use wood just pick up some aluminium sheet. Its not too expensive and then draw round your shell and attack it with a jigsaw and hacksaw. That way you have got your original for a future pack and a one off special for this pack. Aluminium is pretty easy to work with, just take your time and use sharp blades.
Just wanted to give an update. The mobo is made out of 1/8 mdf. But it bowed cuzz the shell for some reason won’t sit flat. I also can’t find any aluminum sheet to make a nice sturdy mobo. But here she is so far in all her glory.
Looking good!
I’m still trying to find a sheet of aluminum that I can make a more firm motherboard