Hey guys, I need some help. I’ve started working on my pack for my fanfilm, and I’ve started with the thrower (or gun). My problem is that I’v been following Norm’s plans, but the plastic he suggests is too flimsy. The gun body falls apart when I hold it. I let it dry for a day or more, so I don’t think that the adhesive is still wet. What other materials do you guys suggest? I’m thinking wood, but I don’t want the grain to show through when it is painted.
I used matte board. it’s more dense and rigid than foam board. Its pretty damn durable. Plus you can get a huge sheet of it for like 5 or 6 bucks from hobby lobby.
I’ve used Luaun wood for most of my pack construction. It’s a composite wood, like plywood, but it’s a lot lighter, and doesn’t have as bad of wood grain. I’ve used it for most of my pack, and it’s durable, lightweight, easy to work with, and a lot easier to hide the grain on than plywood. Just a thin layer of wood putty sanded down, and you’ll be fine.
Chris
You can always coat your wood parts with fiberglass resin to cover up the woodgrain, just apply it with a brush, let dry and sand down the high spots. Sand with steel wool prior to priming and use a good primer that will fill in minor imperfections.
That sounds about like what I want. But what about lights? Will the matte board hold up against the heat of the bulbs (I don’t really have the money for an ornate LED system so I’m going with battery opperated Christmas lights that are on sale all over town.)?
What about some more of you? Anybody else out there like matte board over some other options? Let me know.
I used that template from hprops and I cut it out on paper and glued them to balsa wood. I then used a razor and cut the parts out. After they were cut I used little half inch blocks to glue it all together. After it was done I covered it with bondo. I’ll tell you it came out PIMP!!
Christmas lights run at a pretty low temperature and won’t pose any kind of threat. They might be a little warm to the touch after extended use, but there’s no way they could ever get hot enough to send your wand up in flames.
Thanks, Radar. I have a strand left up from the holidays and it was pretty warm so I figured I would ask.
And thank you bigjuan2001. I’m going to give that idea a try as well. I need more than one gun, so I’ll see which works best for me (time and money wise).
Thanks to everyone who has responded. And I’m always looking for more help, too. So just keep the ideas coming.
Okay. I’ve got the foamboard to start on the gun.
My question is now, what is the best way to round the top of the box? I’ve heard everything from dowel rods and Bond-O, to just sanding. I’m worried about sanding because the foamboard isn’t that thick; and Bond-O has always given me trouble. But I’m not above using it is it is the best.
What about using some wide electrical tape to create the smooth edges? Do you guys think the tape would show through when it is painted? Or is it better to just leave it square-ish?
Also, what is the best way to attach the handles? I was thinking of using a piece of wood inside the box and using ring clamps on each side of the PVC to hold them. I think the wood would add support to the overall structure of the box and ease wear when holstering and unholstering it from the pack.
I attatched the handles with a two dollar tube of adhesive from Odd Lots. Actually, I made the whole pack with this stuff and you can keep the name brand stuff. This is the toughest glue I’ve ever worked with! Reinforce the corners with small 1/" or 1" blocks and I reinforce all seams with a thick bead from the hot glue gun. I made my thrower from Garage Sale signs and I have no problems with durability.
A good method I found for rounding off the box is hot glueing/gooping your back handle to the inside of curve then take either a piece of matte board and bend the edge to fit the curve then use wood filler to fill in the gaps. You could also use a piece of plastic from a for sale sign and use that for the top but you may have to reinforce it to keep it from caveing in. The matte board top is really strong.
As for attaching the handles I hot glued the back handle straight into the gun. I also hot glued my barrel straight into the back wall of the gun box but I was on a dead line when I made my pack and didn’t have the time to put lights in the gun. If you glue the back handle straight into the gun, it does support the box structure especially if you use wood filler around the seams.
The edges of the electrical tape will definately show thru the paint
-Drakk )))
Did you put any support posts inside? What kind of glue are you using?
I haven’t made the box yet. Probalby going to start this weekend. Right now I’m taking notes from others and their wisdom, plus I’m waiting on my co-everything to come over and help with this…because of the budget, we’re going to have to make our own packs and doing to together will hopefully insure accuracy.
Right now, I’m just making a model to see how things fit with the pattern I’m using. I’m using foamboard for this stage, but probably will be using a light wood for the acutal construction. But I want the foamboard to look as good as possible because I may use it as a stunt pack. So for that I’ll be using Elmer’s brand super glue.
Since I’ve decided to use wood for the final construction, I was wondering if it would benefit me to purchase a Dremil tool? I’ve always wanted one and with the intracate detail of these packs I’m sure it will help. Anyone else out there avid fans of the little tool?
When building a pack , the dremel is an tool that is necessary, its not as clumsy as a jig saw , but powerful enough to cut/sand.
and I use mine more than I realize ,especially if you scratch build.
Yep, get a 10 speed Dremel and lots of attatchments. ![]()
Well then, Meijer, here I come.
Will the Dremil also work well for cutting through the cake pan cyclotron? Because I’m worried about denting the pan with a regular drill.
My solution for putting holes in the cake pan:
Get a hole drill bit (Not a flat/paddle bit, just ask at the hardware store) slightly larger than the hole in the center of the washer/whatever you’re putting around the light holes. Then clamp the pan to a piece of scrap wood or two (make sure it’s taller than your pan is deep) You want the wood to touch the work surface, not the pan. Line up the hole bit with your premeasured marks and drill very, very slowly. The wood underneath the pan will help keep the bit lined up and the pan from getting dented, and if you have access to a drill press, even better. Just remember, go slow.
One other note: These bits are not cheap. But it’s still cheaper than replacing 10 ruined pans. (trust me, I’ve learned from experience.)
One of these babies:
Also put a block of wood under the pan to absorb all of the pressure. If you just drill into the pan with nothing under it for support, then its going to collapse.
Can I cut the cake pan with a Dremil? I would like to save as much as time, labor, and money as possible.