Foamboard pack construction

I really want to have a pack based on Stefan’s plans. I also want to have it done by Halloween. Problem is, i can’t afford a pack shell. So a month ago i started construction of a pack shell made of foamcore. After the shell is built i will reinforce the inside with GreatStuff brand spray foam. Some of the corners are a bit rough but that will be fixed by sanding and priming. Here are some pics of my progress so far.

image

image

image

image

looks awesome!

YES! You are my new best friend.

I built a ghost trap using foamboard, but I was having doubts about the effectiveness on a proton pack. I’ll be watching this project closely.

:cool:

wow that is looking awsome! i’m also building my pack shell in a similar method (using sheet styrene instead of foamcore) so i’ll be watching your build closely to see how you tackle some parts i’m unsure about building myelf :slight_smile:

what are you goiing to use to seal up the foamcore?? i was going to do this but nothing really worked well to seal it

Griff

I used bondo and wood filler.

i haven’t used foamboard in forverand i can’t rmemeber i know foam is in the middle but is plastic or paper sandwiching it

http://en.wikipedia.org/wiki/Foamboard

so you plan on sealing the inside with spray foam? Are you planning to fill the inside completely or just inject the corners? Just remember that spray foam expands so you will have to keep one side open, and the be careful how much you put in there or it will rise like bead, bust the seams, and take two days to dry. But if you’re just reinforcing the corners and whatnot you should be fine. Great build so far!!!

wow - whatever happened to this… hows it going?

Yeah, I’d love to see how it’s going too. It’s a great idea for cost effectiveness and for making it lighter on your back!

srsly! Just wondering how it holds up…

I made a lot of props, including the head for Pyramid Head, out of foamcore. I must know how this turned out!!!

Thanks for the compliments. I really need to post updated pics. I just ordered parts from Irricanian to complete the pack and gun.

I was asked how i cut the foamboard so everything lines up neatly. The spacer was the hardest part. For that i cut the top face out of foamboard and used posterboard for the side face. Then i stuck bits of foamboard on the inside to reinforce the posterboard. Then it was further strengthened by the plating.

Below is an example of how i cut out my ion arm. The rest of the boxy parts were done pretty much the same.

First I draw all of my measurements on the foamboard. I used Stefan’s plans. Next I cut all the way through the red lines. For the black lines (hinges) and green lines only cut through the first layer of paper and foam. Leave the bottom layer of paper intact. Next, bend the hinges open and remove the portion in grey. Remember to leave the bottom layer of paper. Next, bend all of the hinges closed to test the fit. If it all looks good, open it up, glue the hinges, and close it up again.

The portions in grey are NOT extra space between your measured sides. Their width should be the same as the thickness of your foamboard. 3/16" or 5mm in my case.

wow - thanks so much for that explanation - it’s fantastic!!!

Really appreciated! Looking forward to new pics!

I’m interested to see how this thing turns out…so keep this thread going!!

Thought I’d post an update with my progress so far. I got my particle thrower parts from Irricanian a few days ago. I also ordered the extra bits and bobs for the pack. My construction is pretty much done. Just a few more pieces to glue on. Then I’m going to paint whole thing in a thin layer of latex paint. That should keep the foam protected. Next, the black spray paint. Lastly, the labels, barbs, elbows, resistors, wires, etc. I can’t wait to start on the thrower.

Here’s a pic

WOW! That looks great! What did you use for the bottom extensions at the bottom of the pack? Is it foam?

All of the plating around the spacer is just foamboard rectangles. The two thicker pieces of plating are just small foamboard boxes. I made them the same way I made the ion arm.

looking killer! i don’t know if you’re interested, but i sealed up the foam edges of the foam core on my props with…cut sections of cereal box. it glues down neatly, paints smoothly… worked great. my ghost trap shows it best… good luck.