Plz help an idiot!

K as the topic says I’m an idiot when it come to mechanical applitude. I’m in the prep stages of building a pack using exorays v71 shell and resin parts, here’s the catchbi have no idea what tools I need to have to build this pack, I.e. A dremel and so on. Plz list tools I should have before I start building this pack! Ive never worked with fiberglass so idk how this is going to go.to be frank I’m kinda being reserved starting this pack cause I’ve never done this before! Help plz! Thx everyone

Chris

You shouldn’t need a dremel at all if you go the pre-cut version as I did all the trimming for those…

Basically a drill and a drill bit set, a screw driver both philips and straight will get you off to a good start… Some pliers, a hand saw, a wrench, file and sandpaper will come in handy as will other tools along the way but there is no right or wrong way… I personally have a vast assortment of tools both hand and power at my disposal, the tools I use and the way I do it won’t be the same as others that don’t have access to the tools…

My advise hit up Home Depot and get a Ryobi cordless drill, and circular saw set, and maybe the jig saw, total price should be about $100 and they are decent tools that should last for many other projects…

Allen wrench set, 2 part epoxy glue…

Awesome feedback I’m eating this up! Plz anymore feedback on preplanning and set up would be amazing!

Thx guys!

covering my eyes …cant bear to see exorays shell in the hands of a total novice… :sigh: Nah…just kidding…But damn…i wish i had an exoray shell as my first project. Its like never working on a car before..and you decide to tinker with a ferrari.

I’ve built a hotshot gun kit before and thatbwas horrible secondary to the quality of his kits. But I’ve never worked with fiberglass so I’m looking for advice or tips that I should know. Trust me I’m doing my homework and research so not to many worries and I hope pics of my progress proves my worthy to the gbfans community Haha

Don’t over think it, working with fiberglass is the easy part it’s creating the part that is hard…

For those building one of my shells all you really need to do is, sand, drill a few holes and glue/screw some parts on… Treat it like any plastic model part as fiberglass isn’t really anything unique or special…

Should I worry about cracking or splintering the fiberglass if I drill to hard or anything?

Measure twice…cut once and let the saw/drill do the work, don’t force it. If your blade/drill is sharp you only need to guide it.

Some basic hand tools are always good to: screwdriver set, allen keys, hacksaw, files, drill bit set and #8 and #10 and 1/4" taps for putting in threads for the bolts on your pack.

And the #1 tool…patience! Take your time, think it thru and it will turn out

Have fun!

Awesome. Thx for everything guys. If anyone else has suggestions, coments or feedback plz let me know. Also anyone have tips on epoxy?

Read the label, they all have mixing instructions for best results and check the type of materials they are suitable for. Oh and wear gloves and glasses

Ya that’s whatbi was wandering. Do u need copious amounts or small doses go long ways? Sorry bout all the noob questions I just want to be prepared u kno?

epoxy goes a long way, you should only need a small amount for securing any part. chances are, if you smear on the exopy, then press the pieces to be secured together and any epoxy oozes out the side you have too much. also, there is a thread on here dedicated to the construction of exoray’s shells here:

i’m sure you can find many answers and resources there…good luck, and POST PICS!!!

Also, while we’re on the subject of epoxy and two-part mixes, If you have gaps bigger than 1/4", you might wanna try epoxy putty. That usually works up to 3/4" before it get’s too stressed and breaks at the bonding point. (depending on where you put it.)

Bondo is a very good filler, but if you’re using a pre-made shell, stick with regular epoxy and putty epoxy. getting extra fiberglass resin and mats are easy, but they require lots of layering and plenty of sanding, not to mention the ventilation.

The shell will most likely not crack with drilling, but make sure you measure everything 3-4 times before drilling. Like I said, if anything happens, don’t panic. Just remember, epoxy paste and epoxy putty will fix anything that happens with fiberglass. Keep your wits about ya and play it cool. Patience will get you far.

Awesome thx alot for everyones feedback and help! I will def post pics, keep everyone updated, and I’m sure I’ll be askng questions later on.

In my case:

  1. I found a miter box was extremely handy when cutting dowels for certain parts of the pack.

  2. Tapping tools - one of the best tools ever (thanks Colin!)

  3. Dremel

  4. Drill

  5. 7/32 (IIRC - check the V71 build up thread) long drill bit

  6. Plumbers epoxy putty

  7. Sanding paper (various grits and wet sanding)

  8. Files

  9. Clamps/vice

  10. A laptop as close as possible to your working area

  11. I’ll keep adding some stuff when the boss is not around (hehehe)

Awesome list thx bro