Scaled Neutrona Wand Build for Fiancé's Pack

Hello to everyone on the board. I wanted to create this build thread for a little project I started today. I’m a huge Ghostbusters enthusiast and I have suckered my fiancé into cosplaying with me. She’s a tiny human, about 5’2", so a full-size proton pack is proportionally wrong for her, but the Spirit Halloween pack is pretty perfect.

I first modified her Spirit pack a few years ago but the wand always bothered me.

After kicking around the idea of starting a new pack for her then deciding to just mod her current pack more, I knew I HAD to change out the wand. A good buddy of mine had an extra 3D printed scaled wand kit and donated it to me, warning me it was pretty rough and needed a lot of clean up.

So, on this sunny Sunday, I decided to start this project. So here we go! I started by Bondoing some of the parts then did a little sanding.

I had also been wanting to add a rotating grip, but the kit wasn’t designed to include this feature. Instead, it had that nub the aluminum tube was supposed to fit over, except it didn’t fit at all, so let’s start cutting it up!

That worked out better than expected…

I had been planning this for a couple weeks, so I found a PVC tube that would fit inside the aluminum tube. It’s long enough that it will bump up against the back of the inside of the wand. I drilled out the front to support it, but will mechanically connect it along the back side and hide it behind the fuse box and rear cylinder.

Then, I wanted it to have the short aluminum ring separate from the main tube, so I cut it by hand and and drilled out some holes for the hex screws.

I also drilled out holes for hat lights and an arcolectric lamp. All of are full-size, but I think they scale well enough with this wand body

And finally, I have the rear aluminum tube getting epoxied in place.

I have a Frankengeek electronics kit to install still and I’m letting the epoxies cure for 24 hours. I may try to do some painting tomorrow if it isn’t too humid. I also grabbed Moby Sign Company’s Hasbro kids wand labels that appear to be the perfect size for this bad boy.

This is looking great and can’t wait to see it complete! Love to see how you’re taking it up a notch by making the rotating grip. Glad this kit found a loving home!

I decided to start doing some painting… updates should be incoming. I’d love to throw some labels on tonight…

I did a little more work. I’m going to try to get the electronics in there today and paint the grips.

My plan for the grips is to paint them orange then clear coat them, then do a spray of black on top with the hope that over time, the black will wear off any naturally weather to the orange undercoat, replicating how the packs look today.

So, I had to pump the breaks a little bit but I did get to paint the grips the first coat.

My plan is to clear coat them then paint them in satin black but not coat the black, that way, they wear away to the orange.

I also picked up some brass washers and replaced the ones on the front grip ring.

Little stuff like that makes me so very happy. I need to pull apart the old wand so I can liberate the toggle switches then I can worry about the electronics.

Ok, crusin’ along on my “little” wand project. Last night, I ripped out the electronics kit from the existing Spirit wand. The pack is running a Frankengeek scaled kit, so I got his 80-90% wand kit but I needed to two toggles from the pack kit. That was a whole process and let’s just say I will never be using that old Spirit wand again.

As for the new wand, I got the wire harness inside and mounted the two toggles inside the gun body. I also replaced the loom with correctly scaled 3/4" OD loom. I drilled a small hole into the rear aluminum tube and because I’m insane, I used the screen accurate connection method with two vintage Panduit 6" zip ties threaded through each other and holding the loom in place. I also glued in place a reflective cup for the vent light, the milky hat lights, and the arcolectric lamp.

Now order some Chinese food and have it out on the table with the yellow multimeter while you eat.

And a can of Tab on the side.

Tonight’s progress.

Did a fitting of parts tonight. The only major piece missing is the trigger box. I had a little fail last night as a result of dull drill bits, so my goal this weekend is to get that fixed. I need to do some finishing work on the gun track but this gives a good idea of what it’ll look like.

So, the wand is mostly done and I think it came together pretty well.

I think it looks pretty good for a Spirit Halloween pack.