How to make a Replica props sound kit louder?

I have those same 8ohm speakers I think, running a pair of them also, if they’re the ones I think they are. The Canuk amp, also. It’s odd, indoors when I work on the pack it’s plenty loud. Not deafening or such but I can hear it across a couple rooms, with shell on. But taken outside for some reason I can’t hear squat. Not that there’s heavy traffic or any type of noise drowning it out, just a tiny sound signature outside. In part due to the obvious acoustic advantage of the house walls, but I didn’t think it’d be so drastic a difference.

So going to gamble and give these a try, just ordered 'em. Not sure if I’ve overlooked anything, probably havee. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=320471509788&ssPageName=STRK:MEWNX:IT 5 1/4" Kenwoods. It’s only 4ohm, not 8ohm, but the speaker is being powered from the amp (which I believe I read is good for either 4ohm or 8ohm) not the RP sound chip. Good power range to play with, 2-28 watts RMS. And it’s shallow, great for inside a pack. Top-mount depth (height) only 1 3/4" so placement will be easier.

I am hoping a single one of these speakers will produce a larger sound signature than my current setup. If so I’ll chime in and give the good word.

Getting louder also requires you to have good quality speakers. And when you use multiple speakers you need to pay attention to how you wire them.

Since the requirement is 8ohm you need to look at the chart

If you wire 2 8ohm speakers in Series you end up with 16ohm

If you wire 2 8ohm speakers in parallel you end up with 4ohm

So using 2 speakers with the sound module you either want to

  1. wire 2 4ohm speakers in series to get to 8ohm

or

  1. wire 2 16ohm speakers in parallel to get to 8ohm

here is a good read on this subject What Do Speaker Impedances Mean? | Atlantic Quality Design, Inc. Musical Products

Thanks Rob, that just answered my next question.

I got one of the 7 watt mono amps Mburkit suggested as well as the 12 volt power supply, so I’ll be hooking up the 12 volt to the amp, and a 3 “AA” cell pack to the sound board

Does it matter what wattage the 4 ohm speakers are? or is it just the ohms that matters? What would you recommend?

The watt requirement for the amp is 7 watt, so anything over that will be safe.

Just no too high. Using a high end (120+w) car speaker will be less effective than a cheapo 10 or 15 watt speaker.

True

Thanks for the link Rob, I was just going to ask if it were possible to mix up wiring speakers both in series and parallel and I got my answer from that link you provided.

Thank’s for the info on this, it could not have come at a better time. I just received my Replica Props chip a few days a go and I was just now getting around to start working with it.

This is a great speaker refresher!

Thanks again!!!

Hm, i didnt know that about the speakers. so i have 16 ohms going thru then. Still though, wen i crank it up, theres too much bass and gets distorted =\

You kinda have to. Its what makes it possible to hook up 12 subwoofers in a car without needing 6 amps :slight_smile:

oh and xtrmn8r…

you made a whole wall of replies.. haha

Heh, also did u rly use that AMP? or were u just saying u cud use it.

I wonder how these speakers would work out with the amp?

http://cgi.ebay.com/TWO-REPLACEMENT-4-ohm-70-WATT-MINI-4-WOOFERS-SPEAKERS-/290401054036?pt=Speakers_Subwoofers&hash=item439d406d54

The kenwood?

Got them in yesterday (The Kenwood KFC-1362S speakers), did a quick hookup to test the volume levels of the speakers. No difference, they’re both the same volume. One set of speakers is the 4" ones that sold out a while ago, and one set those Kenwood 5 1/4". The amp goes up to a certain volume and peaks out, doesn’t increase any more. Oh well. Was hoping a slightly larger and better built speaker would produce a larger volume. Bummer.

But they are however well built, a little cleaner sounding, and shallow in height so great for fitting inside the pack without trouble. And I got them on the cheap with free shipping. So it’s a partial win.

A speaker can only output what the amp can put out… If you want more power to the sound, you need a higher power amp. Which would mean also a stronger power source to feed the amp.