Low Budget Proton Pack *WIP*

I finally completed the plans for my motherboard. As I get more and more done with this I will post more.

I’d suggest using Stefan’s plans, they’re a thousand times more accurate than Norm’s. I have them enlarged to 1:1 scale instead of 1:2 scale here if you’d like to use them: http://www.gbfans.com/community/viewtopic.php?f=2&t=14044

Definitely looking forward to seeing what you do with it though.

So it’s been a while since I started on this, and I finally have some sort of progress to report.

I switched to Stefan’s plans for the Mobo and have successfully got it cut from 1/4 inch MDF. I have also cut out of the pieces for HProps plans for the Gunbox from 1/8 in plywood and am in the process of sanding the edges down so I can put is together. At this point I want to know if anyone can suggest a method of holding it together until I can apply a coat of Bondo to it for strength? :garrett:

Wood glue?

So I took pictures of my Mobo and Gunbox parts, thought I’d post the progression for ya’ll

image

image

Made some more progress today. Here’s pics. I used Hot Glue to hold pieces together while I do some test fitting and placement checks, will be using a more permanent solution when I am ready to do final assembly.

image

image

[quote=“pagrashtak”]
Made some more progress today. Here’s pics. I used Hot Glue to hold pieces together while I do some test fitting and placement checks, will be using a more permanent solution when I am ready to do final assembly.

Hole on the front for the light should be on the other side.

Thanks Alkaline, I will remember that when I got to put it together,

sure thing :wink:

So I got all my edges sanded and beveled, it fits together nicely, but I had the same piece on their backwards again, must remember to get that right when I glue it on permanently.

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_gunbox3.jpg)

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_gunbox4.jpg)

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_gunbox6.jpg)

I will be using hot glue for my welds since they look so nice even here.

Finally got the main box glued together, if I am planning this out right, I can now coat it in bondo and start of the other portions of it.

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_PICT0007.jpg)

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_PICT0010.jpg)

The angle of the gun box, the circle have to be oval because the pipe is going straight in there.

To help you out, cut an extra pipe at an angle of the box and than use that extra pipe to draw the oval on the box.

I believe you have the front tube in the wrong hole. Should be palm rest on the left, gun tube on the right.

Ya, i thought so, so I looked at reference photos again, and it is now in the process of having the glue dry so it’s fixed.

What kind of wood you using for your gun?

1/8 in thick plywood, i forget what it’s made from, but I want to say maple…

You know what works good for smoothing out hot glue? A mini or pencil torch.

Got to do a bit more work today. Many thanks to Aurora GB for his assist on getting my parts sanded smooth and corner rounded.

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_PICT0015.jpg)

oh ya, I got Dan Aykroyds Autograph.

I got my rear handle installed today, it’s not perfect, and has a nice up-angle on it, but it will work for now. if anyone has an idea of how to fix the angle without rebuilding any parts, I’d love to hear it.

![image](http://www.gbfans.com/images/pb/pagrashtak2002/Proton Pack_1125091816.jpg)

yeah i think you’re gunna need to fix that rear handle angle. if you lengthen the hole in the gunbox a little you should be able to lower the handles angle. Do it little by little until its just right.