Ectotainment thanks man !
Hello!
I have this built into my pack, which I’ve had since 2015. My e-cig finally ran out of juice. So I went to refill it tonight after researching how to do so. I filled up the tank with the extra e-liquid I had stored in a box, however my vent isn’t putting out any vapor. Has anyone run into any issues like this and did I miss a step somewhere in the refill process?
Thanks guys!
[quote=RJMonette88 post_id=4934708 time=1589333439 user_id=42465]I have this built into my pack, which I’ve had since 2015. My e-cig finally ran out of juice.
[/quote]
Hello chap,
I’m absolutely no expert on proton pack, mods or electronics… but I have been a vaper for about 7 years.
If you’ve had your vape for that long and only now run out of eliquid, did you change the coil (atomiser) when you refilled it? These things tend to degrade and clog up over time.
If you did, are you still getting the crackle sound of a fresh coil? You might need to switch off the fan to hear it.
Did you prime the coil beforehand?
Do you have a vape mod or something similar with which to test the atomiser?
It’s worth noting that some eliquids are conductive, so if you’ve inadvertently spilled any on the contacts that could need cleaning up before it’ll work again.
Alternatively, you may just have a duff coil. They’re only intended to last a couple of weeks and are mass-manufactured by machine, so you do sometimes get a DOA one.
This is all really great info. Thank you! I know nothing about e-cigs or vapes, so your wisdom is greatly appreciated! I did not change the coil, so I’m sure that potentially has something to do with it. Any tips on changing the coil?
Tips?
Heck, loads… I’ll try not to overload you with too much.
As a quick primer:
Essentially a vape is just a wire coil that heats up when current passes through it, bit like a lightbulb element.
This coil is wrapped in a cotton wick, which soaks up the eliquid like in an oil lamp.
When the coil heats up, it heats the liquid on the wick, vapourising it. When you draw on the e-cig, or in your case pump air through the intake, that vapour billows out the mouthpiece in nice white clouds.
So, that’s the fundamentals of how just about every vape works and what’s going on with this kit.
There’s a bit more to it when you get into things like Sub-Ohming for those ridiculously big clouds, and you do have to be careful not to have too low a resistance on the coils, as you can exceed the maximum continuous discharge current of your battery, with **explosive **end results. Most reputable coils have their resistance clearly stated (usually printed right on them) and there are plenty of online “vape calculators” that help you figure out the maximum safe voltage or wattage for that coil.
One major component of eliquid is Vegetable Glycerine and it’s this part that produces the clouds. The higher the VG content, the thicker the clouds (and the more smoke alarms you’ll upset!
). VG is an extract from things like soybean and coconut, and is a thick, syrupy, sweet liquid. Because the coil is actually touching the soaked wick, continually heating VG leads to a build-up of ‘burnt sugar’ gack on the coil, which inhibits the wicking process and eventually your coil will burn out. This is why it needs replacing after a time. How often depends on use.
As for filling… It can depend greatly on which atomiser you have. If you know exactly which one, let me know and I’ll look further into it for you.
However, looking at the diagram posted above, that one looks like a standard Clearomiser. I heard Kanger T2 mentioned somewhere…
That’s pretty easy, but best shown in a video (there are loads): https://www.youtube.com/watch?v=LHJt9mAKEfU
Tip 1: Wait about 10 minutes after filling, to let the wick (strings) saturate and soak the coil, or you could risk burning the atomiser out. At best, that will make your vented vapour smell like burnt cotton. At worst, you burn the actual coil wire and it breaks.
Tip 2: Some similar models of Clearomiser by other brands are filled from the bottom. Make sure you put the liquid between the coil and the inside of the clear tank.
The video above shows a glass dropper, but you might want to make use of a unicorn bottle with a needle nosed tip (they only cost 50p or so) instead.
Tip 2a: Do NOT put the liquid down the central tube or you’ll find it leaking straight out and into your hand… and it’s an icky sticky mess to clean up. Think Venkman after sampling the ectoplasmic residue off the library drawers… but worse!!
Speaking of which, most models of atomiser do NOT like being upside down or even laid flat for several hours, and can leak their entire tank out the end.
Tip 3: VG is a thick liquid. If your mixture is too thick, it won’t wick properly and your wick will burn. Too thin and it will leak.
For something like the Kanger I would normally suggest no thicker than 50% VG, but that is usually mixed with 50% PG (Propylene Glycol). You can buy 50:50 VG/PG unflavoured and nicotine free eliquid easy enough, but a small number of people are sensitive to PG.
There’s no real need for PG in this kit, as you’re not vaping on it, but too much water can upset the balance due to its lower boiling point. Try around 40:60 VG-water and spend some time experimenting with just the kit uninstalled.
Another alternative is 25:75 ratio of VG to Propanediol.
Tip 3a: When mixing your own, it’s often easier to do it by weight than volume.
Bonus DVD tip: I haven’t seen exactly how these vent kits look when assembled, but you’ll want as much air as possible to be pumped directly into the airflow of the e-cig. You’ll get better clouds that way and it will help keep your coil cool, increasing longevity.
Some atomisers have the intake up the centre, others have it on the side somewhere. A few even have it up top.
UK vape tanks/atomisers are limited by law to 2ml capacity, but other countries allow more.
Blimey… Sorry, got a bit carried away there. ![]()
Hopefully this has been of some use to you and anyone else reading this. I’ll do my best to answer any further questions anyone might have.
WOW! Your response is fantastic! I feel likeI learned tons already! Thank you for sharing all of that, and the video. The e-cig in the video is indeed the one I have. I’ll try experimenting with this, guided by your tips, and I’ll keep you posted on my progress as it unfolds. Thank you so very much for your really thorough help!
No problem. I quite enjoy geeking out about this sort of thing.
I get why people chose that Kanger tank, but in just my own opinion there are better atomiser tanks to use - Ones that have the airflow intake on the side for starters, which might avoid the issue of fitting the pump hose in close proximity to the contacts on the 510 connector. You might even be able to eliminate either the pump or the fan (but never both), depending on your choice of tank.
IMPORTANT SAFETY TIP (thanks, Egon):
Most vape devices automatically limit the ‘firing’ time to 10 seconds. This is partly to stop the coil from vapourising all the liquid on the wick, which would result in a dry burn and give the liquid a few moments to re-soak the wick… but you can also set the wick itself on fire if you dry-burn it!!
It’s also to stop the coil itself from burning out, from overstressing your battery and from putting too high a continuous discharge on it (remember the explosive result I mentioned above?).
I don’t know what circuits people are using to control the voltage and duration going into these e-cigs, but make sure they’re at safe voltages for your chosen batteries and limit the firing time, as well as allowing a good 20 seconds to re-wick before you next ‘vent’ your pack. ![]()
Here’s a simple calculator: https://www.myvaporstore.com/ohms-calculator-for-vape-safety-a/292.htm
And here’s an insanely in-depth one, for those that like the geeky details: https://www.steam-engine.org/
VERY good info to know!
Having gone through all that, I have to say that when I’ve seen this venting effect in person, it looks freakin’ awesome!!!
If I ever do a pack build of my own, I’ll want this!
It’s a hit and attention grabber every time!
Here a tip of you mix your own liquid. I make mine with vegetable glycerin, distilled water and a drop of vanilla extract. Unfortunately, I mixed in a little too much water and I was having some leakage issues, but if you boil the liquid, you can boil off some of the water and regain a higher glycerin content. Distilled water without minerals will help extend the life of the coils.
Aqueous Glycerine would be better than water for this kit, though (even distilled). Maybe 10% to 90% VG.
The most you would likely want is 20%.
Ok, so I bought a replacement e-cig, but then realized it’s a different model and I cannot remove the center coil. I did however now find online proper replacement coils for the model of e-cig that is installed in my pack. One question though… When buying replacement coils, they ask what resistance… 1.5 ohm, 1.8 ohm, 2.2 ohm, or 2.5 ohm. Now I’m completely lost as which resistance to get and I can’t really see which resistance mine currently has. I believe the power is getting stepped down to 6v going into the e-cig. Any light to be shed here?
[quote=RJMonette88 post_id=4935023 time=1590009484 user_id=42465]I believe the power is getting stepped down to 6v going into the e-cig. Any light to be shed here?
[/quote]
In short, it doesn’t really matter so long as your battery is rated for the Amps your tank will be drawing.
Generally, the lower the resistance (ohms), the more your device will chuck out huge great clouds of vape… but it will also require higher power input, which means more batteries. This is more of a concern with Sub-Ohm vaping (ie less than 1.0Ω), where you will be putting 75w through a 0.2Ω coil, but still worth bearing in mind.
At 6volts, ie 24w, these coils will be commanding:
1.5Ω - 4A
1.8Ω - 3.3A
2.2Ω - 2.72A
2.5Ω - 2.4A
So assuming that 6v is correct, as long as your battery is rated for more than 4A continuous discharge, you’ll be fine.
Personally I’d suggest going as close to 1Ω coils as possible, so the 1.5Ω coils will be pretty reasonable. How much ‘smoke’ do you want to vent, anyways? ![]()
Out of curiosity, which model is your replacement and why can’t you get the coil out?
Really great info! Thank you for that!
I got the KANGER CE4 LONG WICK CLEAROMIZER as a replacement, but the one installed in my pack is the Kangertech eGo/T2, which has the ability for coil changes.
Yeah, unfortunately the CE4 is one of the few models that does not have a replacable coil.
Very unusual these days, as most people prefer replacable pods. Looks like a bit of bad luck in the selection department.
Personally I’d have suggested an Innokin Zenith tank.
Ectotainment, do you have some finished photos of the vent kit? I’d love to see a couple close-ups of how you drilled a hole into the ecig adapter for wiring as well as how you have the full kit mounted.
I too am having to create a replacement for a potential Fincher because they have all but gone radio silent.
Thanks!!
Sorry for the delayed response… Here are a couple of images of the vent kit in the pack. Sorry I don’t have an image of the drill holes in the adapter since they are covered in glue and shrink tube. You can also see I have added 4 additional colored LEDs to the vent housing, these are an alternate lighting source when I have the smoke system powered off.
Also, I’ve since inverted the ecig to avoid fluid leakage.
Thats a very tidy pack! Are those two 6,000mah batteries? How long do they keep your pack running?