Wharin's Stunt Trap Fun Time build along! (Pics Intensive)

So after getting my pack and gear built and in order, I decided I needed a trap to balance out my already over-crowded belt setup. To this point, I had never scratch built a prop before. I had always worked with mostly unfinished premade parts or kit parts, but I’ve never done a complete scratch build.

After reviewing the many builds and plan sets, I decided to use venkman71’s hero trap plans as they were the most detailed and provided a good platform for me to work off of. I decided to use 1/2" and 3/16" MDF as my main structural materials and use stainless steel sheet metal for the side plates, finishing with most of the found hero parts to keep it authentic.

I first went through and modified most of the measurements to account for material width then laid out all of my MDF:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap1.jpg)

After a few hours of work with a bandsaw and that there jig saw, I ended up with a fine pile of parts:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap2.jpg)

I started first with the stacked parts and the trap cartridge because there was a lot of the thick material to work with. I used a combo of tightbond 3 wood glue and flush finish brad nails:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap4.jpg)

Here’s a shot of the completely assembled stacked parts and the cartridge:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap3.jpg)

With that done, I turned my attention to the trap base and side construction:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap5.jpg)

With the main body of the trap done, I turned my attention to the cartridge. I glued on and added the wings to the bargraph panel, and using a hacksaw, put the groove in for the trap doors to make them look like two separate doors.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap6.jpg)

Check the fit in the main body, and added the handle to the post. I pre-drilled and countersunk a woodscrew through the handle, and glued the battery box to the main body after sanding the sides even on a belt sander. Its starting to look like something!

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap7.jpg)

After those pieces dried, I glued and assembled the rolling base to the cartridge, and predrilled and fitted the wheel axles. then glued the rolling base onto the main trap body:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap8.jpg)

Final dry fit before stage two…Painting!

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap10.jpg)

This could not have come at a better time! I’m starting to acquire all my parts for a dual trap build.

Part two: Paint

After three cans of high build primer, i go everything wet-sanded and mocked up. you can see how anxious I was to layout the caution stripes on the doors…

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap15.jpg)

After a week of spraying black high heat semi gloss, I got the paint finished for the most part. on the trap doors, I laid a base of yellow enamel, wet-sanded it, then taped off the stripes I wanted to keep yellow and sprayed the back over it. I did about six coats of paint on every part, pausing after the third to wet-sand it down to even it out.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap16.jpg)

Tapes off and everything wet-sanded level with 1000 grit wet/dry paper. On the battery box cover, I used the old weathering technique of spritzing some mustard over the surface I wanted to weather before I primed and paint, and it gave it a great wear pattern I was quite proud of:

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap17.jpg)

I then sprayed three layers of matte finish polyurethane and while I let it cure, turned to work on the rest of the trap. I did the assembly work on the side plates. I got my side robs, skirted teardrop knob, and front instrument plate from nickatron, and the cal-r resistor and vector plate are from the gbfans shop. i also picked up a set of lucky skateboard bearings for the wheels with some flashy green rims.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap11.jpg)

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap12.jpg)

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap19.jpg)

I then turned to the electronics. Since I set this as a stunt trap, the doors were not going to be functional and there was no room for a working bargraph, so I wanted to at least have the switch work and the red pilot light blink. Using a astable 555 timer circuit, I worked up a blinking light with a battery and a switch!

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap13.jpg)

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap14.jpg)

It works AND fits!

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap18.jpg)

Final assembly time! I drilled all mounting holes and tapped them for the allen cap screws, and attached each plate with the threads with some epoxy thrown in for good measure.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap21.jpg)

Now came the time to figure out how to keep the cartridge in the trap casing. Since I wasn’t using the track like the hero, I devised a pattern for rare earth magnets! I used 6 on the bottom, and 6 on the back panel, and it holds in strong.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap20.jpg)

After I figured that out, the rest of the assembly was a breeze.

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap23.jpg)

Now for the fun part, the weathering! I took a page out of buckfutter’s Trap Mod Thread and using a burnt wine cork, added some ashy smoke residue to the trap doors. and using some pewter rub n’ buff and a silver sharpie, worked over the trap itself for damage. then using some coffee(black, no cream or sugar) worked over the labels and the trap doors a bit more, and gave it a dusting with powdered fullers earth. the end results came out fantastic!

![image](http://www.gbfans.com/images/pb/methos5150/gbfans trap build_trap24.jpg)

This was honestly the most fun I’ve had building in awhile, and I honestly couldn’t have done it without the support of the CTGB, buckfutter, and the countless members of this forum who’ve inspired me to push my building skills. You guys rock!

Man, I’m jealous! That looks awesome! The rare earth magnets are a brilliant idea!

You weren’t kidding when you said you were back. Love it.

Thanks guys, I definitely put a lot of work into it. Glad you like it!

A.M.A.Z.I.N.G.

Do you have a guesstimate as to how much you spent putting it together? You’ve inspired me to break out my jigsaw and put it to use!

not counting paint drying time, about maybe 10-12 hours. if you do your homework and make a solid plan of attack, this really isn’t a hard prop to build at all. I will say I could have shaved off an hour or two if I had more access to a belt sander. but having ejgunth’s jigsaw to use definitely made it go a lot faster at the start. nothing like precise and square edges to save time.

How much does it weigh? It going to hang heavy in the belt?

Thanks again for the write up, I’m definitely doing this!

it’s in the neighborhood of 5 pounds, so its gonna hang alittle heavy, but I’m not worried.

Damn! Looking at this again and it’s still awesome!

Looks like a great project for me to try at a later date. Bookmarked!

Hey, I have a belt sander you can borrow :slight_smile:

Came out great man, can’t wait to see it in person on Saturday

Exactly this. I’m terrible with wood but I may have to try this.

Who the hell rubs dirt and coffee grounds all over their trap? Lame, John. It should look nice and clean…

To each his own I reckon.

Pretty sure he was messing around since he’s the guy with the weathering thread that Wharin referenced (which is great btw) . If anyone is intimately familiar with rubbing gunk on his gear, it’s him :wink:

Whelp, this goes to show that I didn’t do my research. :stuck_out_tongue: I’m currently doing a trap scratch build based off of this one. I’ll make an album once I’m done.